subject

History, 23.03.2021 20:50 sibr4566

Qué entiendes por positivismo??

ansver

Answers: 3

Show answers

Another question on History

question

History, 21.06.2019 12:30

Ineedd ! the senate hoped to learn from the watergate tapes

Answers: 1

question

History, 21.06.2019 21:30

What city of ancient russia was heavily influenced by the byzantine merchants?

Answers: 1

question

History, 22.06.2019 00:00

What country was the philippines declaring independence from in this proclamation?

Answers: 2

question

History, 22.06.2019 00:30

What did the us civil rights movement gain new momentum after world 2

Answers: 2

You know the right answer?

Qué entiendes por positivismo??...

Questions

question

Chemistry, 13.09.2019 23:20

Conversion of mass to moles a continuous feed to a separation unit is 1,000 kg/h of 45 wt% methanol and 55 wt% water, whose molecular weights are 32 a...

question

Chemistry, 13.09.2019 23:20

Two containers initially contain dry air at 40°c. water is added to both containers so that the relative humidity is 30% in container #1, and 80% in c...

question

Chemistry, 13.09.2019 23:20

The enthalpy of vaporization of h2o at 1 atm and 100 c is 2259 kj/kg. the heat capacity of liquid water is 4.19 kj/kg-c, and the heat capacity of wate...

question

Chemistry, 13.09.2019 23:20

Calculate the cell potential for a cell operating with the following reaction at 25 degrees celsius, in which [mno4^1-] = .01m, [br^1-] = .01m, [mn^2+...

question

Chemistry, 13.09.2019 23:20

An aqueous solution of nazco3 saturates at 300 k to form, nazco3.3h2o crystals. 10 kg/h of 35 mass% aqueous solution enters a continuous evaporative c...

question

Chemistry, 13.09.2019 23:20

The halpy of vaporization of h2o at 1 atm and 100 c is 2259 kj/kg. the heat capacity of liquid water is 4.19 kj/kg. c, and the heat capacity of water...

question

Chemistry, 13.09.2019 23:20

Prepare benzoic acid from benzyl alcohol.5 ml of sodium hydroxide, water and potassium manganese are added. how could you tell when the reaction...

question

Mathematics, 13.09.2019 23:20

When given a graph, the vertical line test can be used to determine functionality. describe the vertical line test and explain the reasons why a graph...

question

Engineering, 13.09.2019 23:20

Two factors that can be modified to optimize the cutting processes are feed and depth, and cutting velocity. a) true b) false...

question

Engineering, 13.09.2019 23:20

The highest cutting temperature is located close to the shear zone. a) true b) false...

question

Engineering, 13.09.2019 23:20

The largest source of heat generated in metal cutting is due to friction. a) true b) false...

question

Engineering, 13.09.2019 23:20

Calculate the differential pressure in kpa across the hatch of a submarine 320m below the surface of the sea. assume the atmospheric pressure at the s...

question

Engineering, 13.09.2019 23:20

Increasing rake angle will decrease the tendency for built-up-edge to form. a) true b) false...

question

Engineering, 13.09.2019 23:20

An orthogonal cutting operation is performed using a rake angle of 15°, to=0.012 in and w=0.100 in. the chip thickness ratio is measured after the cut...

question

Engineering, 13.09.2019 23:20

Write the type of chips generated at each of the following cutting conditions, and explain why. a. low cutting speed: b. large depth of cut: c. very...

question

Engineering, 13.09.2019 23:20

How are the polymeric materials classified? give examples of the plastic materials and elastomers? give the difference between thermoplastics and t...

question

Engineering, 13.09.2019 23:20

What is components? what is phases? what is tie line?...

question

Engineering, 13.09.2019 23:20

Avariable speed reciprocating compressor of mass 400 kg has a natural frequency of 16.2 hz. (a) design an optimum auxiliary mass damper, so that the m...

question

Engineering, 13.09.2019 23:20

Specific cutting energy increases with increasing the cutting speed. a) true b) false...

question

Engineering, 13.09.2019 23:20

Two standard spur gears have a diametrical pitch of 10, a center distance 3.5 inches and a velocity ratio of 2.5. how many teeth are on each gear?...

More questions: History Another questions