Physics, 31.01.2022 14:00 elenagarcia123

Electric current is defined as the amount of electric charge passing through an area per unit time, I = Q/t. If 3 coulombs of charges pass through the cross section of a wire in 2 seconds, what is the electric current? (Unit of electric current is ampere or coulomb/second.

Answers: 1

Show answers

Another question on Physics

Physics, 21.06.2019 17:50

Frost wedging occurs when water seeps into a crack in a rock, freezes, and causes the crack in the rock to widen. t or f

Answers: 1

Answer

Physics, 22.06.2019 12:00

In what direction does an applied force move an object

Answers: 3

Answer

Physics, 22.06.2019 14:30

Aweight lifter raises a 1600 n barbell to a height of 2.0 meters. how much work was done? w = fd a) 30 joules b) 3000 joules c) 320 joules d) 3200 joules

Answers: 2

Answer

Physics, 22.06.2019 16:00

What is friction? how does it affect the motion of an object?

Answers: 1

Answer

You know the right answer?

Electric current is defined as the amount of electric charge passing through an area per unit time,...

Questions

Chemistry, 14.09.2019 00:10

The trash cans distributed by the city of mobile are approximately 4 feet tall and have a square cross section with a side of approximately 30 inches....

Chemistry, 14.09.2019 00:10

Asalt-gradient solar pond is a shallow body of water that consists of three distinct fluid layers and is used to collect solar energy. the upper- and...

Chemistry, 14.09.2019 00:10

Ethylene enters a reversible, isothermal, steady-flow compressor at 1 bar and 280 k, and exits at 40 bar. find the required compressor work (kj/kmol)...

Mathematics, 14.09.2019 00:10

What is the reason for each step in the solution of the equation? -5(x – 6) = 10xdrag and drop the reasons into the boxes to correctly com...

Mathematics, 14.09.2019 00:10

On november 4, your bank statement shows a balance of $2,253.18. your checkbook shows a balance of $2,324.34. if there are outstanding checks in the a...

Engineering, 14.09.2019 00:10

Write the equation to estimate heat flow q due to convection....

Engineering, 14.09.2019 00:10

Write the equation to estimate the heat flow in a heat exchanger in terms of a) the log mean temperature difference lmtd and b) heat exchanger effecti...

Engineering, 14.09.2019 00:10

Aclosed system of mass 2 kg undergoes an adiabatic process. the work done on the system is 30 kj. the velocity of the system changes from 3 m/s to 15...

Engineering, 14.09.2019 00:10

Apump provides a flow rate of 0.05 m3/s of fluid with density 900 kg/m^3 while density of water at that temperature is 1000 kg/m3. if diffential head...

Engineering, 14.09.2019 00:10

A30mm square tubing is to be welded to a steel frame and is loaded by a tension of 2kn and a bending moment of 300nm. the weld material is e7020 and t...

Engineering, 14.09.2019 00:10

Do a summary what happen to titanic in the aspect of material(body) and the ductile brittle temperature (dbt) of the material....

Engineering, 14.09.2019 00:10

Explain 3 different condition monitoring techniques for pumps...

Engineering, 14.09.2019 00:10

Asimple vapor compression refrigeration system uses r-22 as the working fluid. the evaporator pressure is 3 bar and the condenser pressure is 20 bar....

Engineering, 14.09.2019 00:10

Air is compressed from 4.3 l, 37°c and 97 kpa to 0.55l inside a piston-cylinder device. the compression is reversible and adiabatic. rair 0.287 k]/kg....

Engineering, 14.09.2019 00:10

Completely and thoroughly explain how flow process charts and flow diagrams could be used in a typical soft drink manufacturing facility located in no...

Engineering, 14.09.2019 00:10

Amass of 500 kg is lowered at a constant velocity of 0.2 m/sec by means of a rope. calculate the instantaneous stress induced in the rope if (a) the r...

Engineering, 14.09.2019 00:10

Consider a finned-tube, cross-flow heat exchanger with both fluids unmixed. this heat exchanger is used to heat pressurized water with a flow rate of...

Engineering, 14.09.2019 00:10

Asteel chimney 30 m high has an external diameter of 1.8 m and is 35 mm thick. the wind loading is equivalent to a horizontal force of 1.2 kn per squa...

Engineering, 14.09.2019 00:10

Apipe of outside diameter 200mm is lagged with an insulating material of thermal conductivity 0.06 w m-1k-1 and thicknes 75mm. the pipe carries a proc...

Engineering, 14.09.2019 00:10

Atwo-dimensional jet issuing from a long slot strikes a plate at angle of 50 with the plane of the plate. this causes the flow to divide in to two par...

More questions: Physics Another questions