Physics, 06.03.2020 23:53 shirlsmith72
Of two blocks (of masses m1 and m2) tied together with a massless rope that passes over a fixed, perfect (massless and frictionless) pulley. In this problem you'll investigate some special cases where physical variables describing the Atwood machine take on limiting values. Often, examining special cases will simplify a problem, so that the solution may be found from inspection or from the results of a problem you've already seen.
For all parts of this problem, take upward to be the positive direction and take the gravitational constant, g, to be positive.
Part A
Consider the case where m1 and m2 are both nonzero, and m2>m1. Let T1 be the magnitude of the tension in the rope connected to the block of mass m1, and let T2 be the magnitude of the tension in the rope connected to the block of mass m2. Which of the following statements is true?
Consider the case where and are both nonzero, and . Let be the magnitude of the tension in the rope connected to the block of mass , and let be the magnitude of the tension in the rope connected to the block of mass . Which of the following statements is true?
T1 is always equal to T2.
T2 is greater than T1 by an amount independent of velocity.
T2 is greater than T1 but the difference decreases as the blocks increase in velocity.
There is not enough information to determine the relationship between T1 and T2.
Part B
Now, consider the special case where the block of mass m1 is not present. Find the magnitude, T, of the tension in the rope. Try to do this without equations; instead, think about the physical consequences.
T =
Part C
For the same special case (the block of mass m1 not present), what is the acceleration of the block of mass m2?
Express your answer in terms of g, and remember that an upward acceleration should be positive.
a2 =
Part D
Next, consider the special case where only the block of mass m1 is present. Find the magnitude, T, of the tension in the rope.
T =
Part E
For the same special case (the block of mass m2 not present) what is the acceleration of the end of the rope where the block of mass m2would have been attached?
Express your answer in terms of g, and remember that an upward acceleration should be positive.
a2 =
Part F
Next, consider the special case m1=m2=m. What is the magnitude of the tension in the rope connecting the two blocks?
Use the variable m in your answer instead of m1 or m2.
T =
Part G
For the same special case (m1=m2=m), what is the acceleration of the block of mass m2?
a2 =
Part H
Finally, suppose m1??, while m2 remains finite. What value does the the magnitude of the tension approach?
T =
Answers: 3
Another question on Physics
Physics, 22.06.2019 09:50
Which statement correctly describes the current in a circuit that is made up of any two resistors connected in parallel with a battery? a. the current in the battery and in each resistor is the same b. the current the battery equals to the sum of the currents in the resistors c.the current in the battery is less than the current in either resistor d. the current in the battery equals to the product of the currents in the resistors
Answers: 1
Physics, 22.06.2019 14:40
During the experiment if you could triple the breakaway magnetic force with all other quantities left unchanged, what is the new value for the critical velocity if it was v0 (initial velocity), initially? (b) now if you halved the radius with all other quantities left unchanged, what is the new critical velocity if it was v0 (initial velocity), initially? (c) if during the experiment, critical velocity quadrupled with all other quantities left unchanged, what is the new breakaway force if its magnitude was initially f0,?
Answers: 1
Physics, 22.06.2019 15:00
You hang a book bag on a spring scale and place the bag on a platform scale so that the platform scale reads 23.7n and the spring scale reads 13.8n. what is the magnitude of the force that earth exerts on the bag?
Answers: 1
Physics, 22.06.2019 16:00
An charge with mass m and charge q is emitted from the origin, (x,y)=(0,0). a large, flat screen is located at x=l. there is a target on the screen at y position y(h), where y(h) > 0. in this problem, you will examine two different ways that the charge might hit the target. ignore gravity in this problem. 1.assume that the charge is emitted with velocity v(0) in the positive x direction. between the origin and the screen, the charge travels through a constant electric field pointing in the positive y direction. what should the magnitude e of the electric field be if the charge is to hit the target on the screen? express your answer in terms of m, q, y(h), v(0), and l. 2.now assume that the charge is emitted with velocity v(0) in the positive y direction. between the origin and the screen, the charge travels through a constant electric field pointing in the positive x direction. what should the magnitude e of the electric field be if the charge is to hit the target on the screen? express your answer in terms of m, q, y(h), v(0), and l.
Answers: 1
You know the right answer?
Of two blocks (of masses m1 and m2) tied together with a massless rope that passes over a fixed, per...
Questions
English, 16.03.2020 20:28
Spanish, 16.03.2020 20:28
History, 16.03.2020 20:28
Health, 16.03.2020 20:29
