subject

Mathematics, 16.04.2021 20:30 adamsc819

Write an expression using vocabulary words to represent each given expression. 8 - 2g

15(a + c)

m + n5

b3- 18

f - d2

ux

ansver

Answers: 1

Show answers

Another question on Mathematics

question

Mathematics, 21.06.2019 14:30

Every time you drive you will experience a combination of driving conditions and environments.

Answers: 1

question

Mathematics, 21.06.2019 15:10

5.(04.07) two different plants grow each year at different rates, which are represented by the functions f(x) = 4* and g(x) = 5x + 2. what is the first year the f(x) height is greater than the g(x) height? year 3 year 0 year 2 year 1

Answers: 1

question

Mathematics, 21.06.2019 17:00

Which expression is equivalent to the expression shown?

Answers: 2

question

Mathematics, 21.06.2019 20:00

Maurice has 54 fewer comic books than rebecca.they have 130 comic books together .how many comic books are in maurices collection ? how many comic books are in rebeccas collection

Answers: 1

You know the right answer?

Write an expression using vocabulary words to represent each given expression. 8 - 2g

1...

Questions

question

Engineering, 14.09.2019 02:10

In laminar now, fluid particles are constrained to motion in (parallel —perpendicular opposite) paths by the action of (temperature- viscosity —pressu...

question

Engineering, 14.09.2019 02:10

Which of the following is not a function of a plc programming device? a. to enter the user program b. to monitor the user program c. to execute the u...

question

Engineering, 14.09.2019 02:10

Acertain measurement is performed 50 times. the arithmetic mean reading is 7.163 ft., and the standard deviation is 0.01 ft. how many readings fall wi...

question

Engineering, 14.09.2019 02:10

Apolyimide photoresist requires 90 mj/cm^2 per micron of thickness to be developed properly. if a lamp provides 900 w/m, how long does it take to expo...

question

Engineering, 14.09.2019 02:10

Determine ixx for the cylinder with a concentarted circular hole. the mass of body is m...

question

Engineering, 14.09.2019 02:10

Two 14.5° pressure angle, mating, 5-pitch gears have 30 and 110 teeth. in practice, the gears are mounted at a center distance 0.7 inches greater than...

question

Engineering, 14.09.2019 02:10

The center distance of two spur gears that have 20° pressure angle and full-depth with diametral pitch of 8 teeth/in, is increased by 0.05 in over the...

question

Engineering, 14.09.2019 02:10

Two meshing 24-pitch, 25° pressure angle gears have n1-24 and n2 60 teeth. the in use center distance of the two gears is 0.16 inches larger than the...

question

Engineering, 14.09.2019 02:10

Batteries are used in a plc's processor to a. maintain data in nonvolatile memory when line power is removed from the processor. b. maintain data in v...

question

Engineering, 14.09.2019 02:10

Acomplex cmos fabrication process requires 25 masks a. what fraction of the dice must be good (i. e. what yield must be obtained) during each mask ste...

question

Engineering, 14.09.2019 02:10

Draw and label a typical true stress-strain curve for a ductile material....

question

Engineering, 14.09.2019 02:10

Draw and label a typical engineering stress-strain curve for a brittle material....

question

Engineering, 14.09.2019 02:10

Determine the length l of each of the slender rods of mass m/2 which must be centrally attached to the faces of the thin homogeneous disk of mass m in...

question

Engineering, 14.09.2019 02:10

Afour-stroke cycle engine delivers a torque of 437 ft-lb at the flywheel (output shaft) when the engine speed is 2100 rpm while using 514 hp of fuel e...

question

Engineering, 14.09.2019 02:10

It takes a man 12.5 hours to complete a 500-mile trip in his automobile, during which 18 gallons of gasoline are consumed. during this trip, the avera...

question

Engineering, 14.09.2019 02:10

For a motor purchased for a tank project, it claims that at 12v it produces 6000 rpm. this motor is attached to a 50: 1 gear reduction gearbox. the ou...

question

Engineering, 14.09.2019 02:10

Which of the two materials (brittle vs. ductile) usually obtains the largest modulus of toughness and why?...

question

Engineering, 14.09.2019 02:10

Afour-cylinder chrysler si engine has the following characteristics: 2.2l displacement, 87.5 mm bore, 92 mm stroke, 8.9 compression ratio, and a maxi...

question

Physics, 14.09.2019 02:10

Abead with a mass of 0.050 g and a charge of 20 nc is free to slide on a vertical rod. at the base of the rod is a fixed 20 nc charge. in equilibrium,...

question

Engineering, 14.09.2019 02:10

Which of the two materials (brittle vs. ductile) usually obtains the highest ultimate strength and why?...

More questions: Mathematics Another questions