Engineering, 07.06.2021 08:00 maddie6610

Name and describe at least four geometric shapes that will be included in the design in the following scenario. Situation: Peter is designing a new hybrid car that functions on solar power. He is currently working on sketches of his design using geometric patterns
and shapes.
B
1
U
á
O Word(s)

Answers: 2

Show answers

Another question on Engineering

Engineering, 03.07.2019 14:10

Amass of m 1.5 kg of steam is contained in a closed rigid container. initially the pressure and temperature of the steam are: p 1.5 mpa and t 240°c (superheated state), respectively. then the temperature drops to t2= 100°c as the result of heat transfer to the surroundings. determine: a) quality of the steam at the end of the process, b) heat transfer with the surroundings. for: p1.5 mpa and t 240°c: enthalpy of superheated vapour is 2900 kj/kg, specific volume of superheated vapour is 0. 1483 m/kg, while for t 100°c: enthalpy of saturated liquid water is 419kj/kg, specific volume of saturated liquid water is 0.001043m/kg, enthalpy of saturated vapour is 2676 kj/kg, specific volume of saturated vapour is 1.672 m/kg and pressure is 0.1 mpa.

Answers: 3

Answer

Engineering, 04.07.2019 18:20

For each of the following process: a) sketch the p-v diagram, b)sketch t-s diagram, c) sketch t-v diagram, d) sketch the boundary work on one of the diagrams (a, b or c) and e) sketch the reversible heat transfer on one of the diagrams (a, b or c): 1- isobaric process from compressed liquid to superheated vapor 2- isothermal process from compressed liquid to superheated vapor 3- isentropic process from compressed liquid to superheated vapor

Answers: 3

Answer

Engineering, 04.07.2019 19:20

Apiping systems consists of 6 m of 6-std type k and 12 m of 4-std type k, both drawn copper tubing. the system conveys ethylene glycol at a rate of 0.013 m3/s. the pressure drop across the system is to be calculated. there are two 90° elbows in the 6-in pipe, a reduction from the 6-in pipe to the 4-in pipe and four 90° elbows in the 4-in pipe. all fittings are soldered (same as flanged) and regular. the inlet and outlet of the system are at the same height.

Answers: 1

Answer

Engineering, 06.07.2019 04:10

An array of m-50 thermoelectric modules is installed on the exhaust of a sports car. each module has an effective seebeck coefficient of sp of 0.143 5vk and an internal electrical resistance of r.-4 ? in addition, : (15 points each module is of width w 60mm and contains n=100 pairs of semiconducting pellets. each pellet hasan overall length of 2l-5mm and a cross-sectional area as 1.2 x 10'm and is characterized by a thermal conductivity of kpl2w rnk. the hot side of each module is exposed to exhaust gases at·p650c with hia4ow rrk while the osite side of each module is cooled by pressurized water at surface) and 156 °c (at the cool surface). 11s c with h: -500w/m'k. the modules are wired n series and the load resistance is r d=400ohm .the module surface temperatures, t, and ts are 183 "c (at the hot surface and 156c (at the cool surface) a)-draw a schematic of this scenario and label all parts. a. b. if the induced current, i, is 0.15 amps, what is the total power (pa) for one module? c. what is the total power harvest from the exhaust with all 50 modules?

Answers: 2

Answer

You know the right answer?

Name and describe at least four geometric shapes that will be included in the design in the followin...

Questions