Same as the book problem but different values.
a suction device is being designed based...
![subject](/tpl/images/cats/User.png)
Engineering, 02.10.2019 03:20 ptrlvn01
Same as the book problem but different values.
a suction device is being designed based on the venturi principle
to lift objucts submerged in water. the operating water temperature
is 50 c. the suction cup is located 1.3 m below the water surface,
and the venturi throat is located 1 m above the the water. the
atmospheric pressure is 100 kpa. the ratio of the throat area
(i. e., the constricted area) to the exit area is 1/4, and the exit
area is 0.001 m squared. the area of the suction cup is 0.25 m
squared.
a. find the velocity of the water at the exit for maximum lift
condition.
b. find the volume discharge through the system for maximum lift
condition.
c. find the maximum load the suction cup can support.
state explicitly the restriction that constrains the maximum lift
(or minimum pressure in the system).
![ansver](/tpl/images/cats/User.png)
Answers: 3
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 03.07.2019 14:10
Line joining liquid phase with liquid and solid phase mixture is known as: a) liquidus b) solidus c) tie line d) none of the mentioned
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
What difference(s) did you notice using a pneumatic circuit over hydraulic circuit.explain why the pneumatic piston stumbles when it hits an obstacle.
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Ajournal bearing has a journal diameter of 3.250 in with a unilateral tolerance of 20.003 in. the bushing bore has a diameter of 3.256 in and a unilateral tolerance of 0.004 in. the bushing is 2.8 in long and supports a 700-lbf load. the journal speed is 900 rev/min. find the minimum oil film thickness and the maximum film pressure for both sae 20 and sae 20w-30 lubricants, for the tightest assembly if the operating film temperature is 160°f. a computer code is appropriate for solving this problem.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Which of the following components of a pid controlled accumulates the error over time and responds to system error after the error has been accumulated? a)- proportional b)- derivative c)- integral d)- on/off.
Answers: 2
You know the right answer?
Questions
![question](/tpl/images/cats/istoriya.png)
History, 25.06.2019 23:30
![question](/tpl/images/cats/mat.png)
Mathematics, 25.06.2019 23:30
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 25.06.2019 23:30
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 25.06.2019 23:30
![question](/tpl/images/cats/fizika.png)
Physics, 25.06.2019 23:30
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/istoriya.png)
History, 25.06.2019 23:30
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 25.06.2019 23:30
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/biologiya.png)
Biology, 25.06.2019 23:30
![question](/tpl/images/cats/mat.png)
Mathematics, 25.06.2019 23:30
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 25.06.2019 23:30
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/istoriya.png)
History, 25.06.2019 23:30
![question](/tpl/images/cats/istoriya.png)
History, 25.06.2019 23:30