lbelle

On site since: 2018-03-05 22:34:38

Age: 16 years

About:

Facebook:

Asked questions: 5

Gave answers: 5

Point: 222

Best answer: 2

Questions

question

Engineering, 26.07.2019 18:20

Which of the following statements is/are valid? (a). tolerances are applied on dimensions, while fits are applied between mating parts. (b). a fit re...

question

Engineering, 26.07.2019 18:20

Athin plate of area, 50 cm^2 requires a force of 12 n to move it inside sae 30 oil at a velocity of 1 m/s. what is the viscous resistance of oil on th...

question

Engineering, 26.07.2019 18:20

Velocity boundary layer thickness over a intermal fixed horizontal flat plate is distance required for the fluid velocity to...

question

Engineering, 26.07.2019 18:20

Two very large tanks, with fluid levels of h, are to be drained completely. one tank has a vertical tube attached to its bottom of diameter d and leng...

question

Engineering, 26.07.2019 18:20

Two tanks at different pressures are connected through a small-diameter passage which allows the fluid to flow from the high-pressure tank to the low-...

question

Engineering, 26.07.2019 18:20

An insulated, rigid tank whose volume is 0.5 m is connected by a valve to a large vessel holding steam at 40 bar, 500°c. the tank is initially evacuat...

question

Engineering, 26.07.2019 18:20

Consider flow over a fixed horizontal flat plate. at the plate's surface the fluid velocity is reduced to zero. this is...

question

Engineering, 26.07.2019 18:20

Sketch a standard symbol for third angle projection method used in engineering drawings...

question

Engineering, 26.07.2019 18:20

Ocean water has a specific weight of 10.05 kn/m^3 at the surface and a pressure of 81.8 mpa at a depth of 8 km. the average bulk modulus for the depth...

question

Engineering, 26.07.2019 18:20

For a certain gas, cp = 840.4 j/kg-k; and cv = 651.5 j/kg-k. how fast will sound travel in this gas if it is at an adiabatic state with a temperature...

question

Engineering, 26.07.2019 18:20

Write the official kelvin-plank statement of the second law as well as a simplified version of it that is more easily grasped. write the official clau...

question

Engineering, 26.07.2019 18:20

You study flow over flat plate. does flow over flat plate have any practical applications?...

question

Engineering, 26.07.2019 18:20

Refractory bricks are used as lininas for furnaces because of their thermal properties. consider a thick furnace wall lining with a refractory bricks...

question

Engineering, 26.07.2019 18:20

Calculate the pressure loss of air in a flat oval duct with a = 16 in and b = 28 in for a volume flow rate of 3000 cfm....

question

Engineering, 26.07.2019 18:20

Cars are aerodynamically designed to...

question

Engineering, 26.07.2019 18:20

Automotive manufacturer is testing the ignition system for the number of on/off switches. seven ignition devices were tested to failure with the follo...

question

Engineering, 26.07.2019 18:20

Outdoor air is at 100kpa, 5 c, and a relative humidity of 60 percent. determine the enthalpy difference and the relative humidity inside a home where...

question

Engineering, 26.07.2019 18:20

Athin plate is located midway between two fixed parallel plates. the 10-mm gap between the fixed plates contains sae 30 oil. what is the area of the p...

question

Engineering, 26.07.2019 18:20

What is a heat engine? state its efficiency (a sketch would be appropriate)....

question

Engineering, 26.07.2019 18:20

The reynolds number for flow over a fixed horizontal flat plate is constant throughout its length. a) true b) false...