subject

Social Studies, 16.12.2021 01:20 LonelyKai

. Where do most ideas for bills come from?

ansver

Answers: 1

Show answers

Another question on Social Studies

question

Social Studies, 22.06.2019 02:30

Which of the following is an advantage of using nuclear power plants to produce electricity?

Answers: 1

question

Social Studies, 22.06.2019 19:30

The patriot act made it easier for law enforcement agencies to conduct surveillance under certain circumstances true or false

Answers: 1

question

Social Studies, 22.06.2019 22:00

What contributions did muslims make to astronomey

Answers: 1

question

Social Studies, 22.06.2019 22:30

What are some examples of native americans were impacted by colonization in america

Answers: 1

You know the right answer?

. Where do most ideas for bills come from?...

Questions

question

Engineering, 11.07.2019 02:20

The bottom of a copper pan,03m i mtained at 8by an electric heater. a) estimate the power required to boil water in this pan b) what is the evaporatio...

question

Engineering, 11.07.2019 02:20

Aheat engine operates between a source at 410°c and a sink at -12°c. if heat is supplied to the heat engine at a steady rate of1,150 kj/min, determine...

question

Engineering, 11.07.2019 02:20

Oxygen is supplied to a medical facility from ten 3.2-ft compressed-oxygen tanks. initially, these tanks are at 2,400 psia and 80°f. the oxygen is rem...

question

Engineering, 11.07.2019 02:20

Acomputer cooled by a fan contains eight pcbs, each dissipating 9w power. the height of the pcbs is 11 cm and the length is 18.8 cm. the cooling air i...

question

Engineering, 11.07.2019 02:20

Acoal-burning steam power plant produces a net power of 350 mw with an overall thermal efficiency 12 kg air/kg fuel. the heating value of the coal is...

question

Engineering, 11.07.2019 02:20

Adisk-shaped part is to be cast out of aluminum. the diameter 500 mm and thickness = 20 mm. if the mold constant = 3.0 s/mm2 in chvorinov's rule, how...

question

Engineering, 11.07.2019 02:20

The areas of conflict between public and private include. a)-the areas of conflict between public and private include. b)- lack of communication. c)-...

question

Engineering, 11.07.2019 02:20

Adiving board is to be designed that is 6 foot long, 14in wide. the maximum load at the end of the beam is 400lb. the diving board can be considered a...

question

Engineering, 11.07.2019 02:20

Liquid water at 300 kpa and 20°c is heated in a chamber by mixing it with superheated steam at 300 kpa and 300°c. cold water enters the chamber at a r...

question

Engineering, 11.07.2019 02:20

An adiabatic air compressor takes in air at 100 kpa, 25 °c and delivers it at 1500 kpa, 364 °c to a constant-pressure air cooler, which the air exits...

question

Engineering, 11.07.2019 02:20

Pressurized steam at 460k flows through a long, thin walled pipe of 0.5m diameter. the pipe is enclosed in a concrete casting that is of a square cros...

question

Engineering, 11.07.2019 02:20

Observe the depth of the case and any evidence of decarburizing in the outer case of the quenched sample....

question

Engineering, 11.07.2019 02:20

Asteel sphere with a diameter of 7.6 cm is to be hardened by first heating it to a uniform temperature of 870c and then quenching it in a large bath o...

question

Engineering, 11.07.2019 02:20

Agas power cycle has air entering at 0.7 bar and 260 k. the compressor pressure ratio is 25: 1 and its outlet temperature is 720 k. the combustor heat...

question

Engineering, 11.07.2019 02:20

Determine size of a standard square key made of 1045 hot rolled steel for a 2 inch dia shaft transmitting 100 hp at 500 rpm with factor of safety 2.5...

question

Engineering, 11.07.2019 02:20

Asquare duct with a 10pa/m pressure drop, .001 pa-s viscosity, and a duct side of .1m with a length of 1m is compared to a circular pipe. compute a)-w...

question

Engineering, 11.07.2019 02:20

Apreheater involves the use of condensing steam at 100°c on the inside of a bank of tubes to heat air that enters at 1 atm and 25°c. the air moves at...

question

Engineering, 11.07.2019 02:20

Consider the heating of a fluid in a tube of constant cross section whose inner surface is maintained at a constant temperature the temperature differ...

question

Engineering, 11.07.2019 02:20

Design a solid steel shaft to transmit 14 hp at a speed of 2400rpm f the allowable shearing stress is given as 3.5 ksi....

question

Engineering, 11.07.2019 02:20

In flow across the tube banks, the reynolds number is based on the maximum velocity instead of the uniform approach velocity a)-true b)-false...

More questions: Social Studies Another questions