Physics, 05.11.2020 09:30 kyliearnell

Idk>?

Idk>?????????????????

Answers: 3

Show answers

Answers

Answer from: lbelle

The correct answer is C

Answer from: Quest

most voltage drop calculators want the distance between the source and destination. then internally, they double it so both the source and return wires are calculated. but you need to know which distance the calculator uses so you're not half of what you should be or double what you should be.

most circuit breakers will not take a #6 directly, so the electrician will have to splice on a smaller pigtail. you also have to upsize the grounding wire when you upsized the ungrounded (hot) wire (see note in 250.122). this will preclude using most cable assemblies, as a cable with #6 copper will most likely only have a #10 grounding conductor. you need a #6 grounding conductor if the circuit is 20a. a #8 cable is no better, as it will have a #10 grounding conductor too. but most 20a breakers will take a #8 directly.

in your related post, you didn't say what type of load this is. if it is a light or heater, voltage drop won't be a big issue. if this is a motor, the current needs are huge at startup and the voltage drop can pose a problem. if this is a motor, knowing if the motor is under much load during startup will answer the voltage drop effect (a saw is easier to start than a compressor).

Answer from: Quest

Answer: a charge of -1.0 × 10⁻⁴ c must be placed at x = 26 m.the sign of the charge will be the same sign as the -4.0 µc charge.======electricstatic force between two point charges is given by $f = \dfrac{kq_1q_2}{r^2}$ where k is coulomb's constant, 8.99×10⁹ n·m²/c², q₁ and q₂ are the point charges, and r is the distance between the two point charges.assign positive to q₁let q₁ = 6.0 µc, q₂ = -4.0 µc, q₀ represent the charge at the origin, and q₃ represent this new charge to place.the charge at the origin q₀ would experience the following force f₀₁ from q₁, with r = 6.0 m (note that 1 µc = 10⁻⁶ c) $f_{01} = \dfrac{kq_0q_1}{(\text{6.0 m})^2}$ the force from q₂ $f_{02} = \dfrac{kq_0q_2}{(\text{15 m})^2}$ the force from q₃ $f_{03} = \dfrac{kq_0q_1}{(\text{26 m})^2}$ the net force on the origin charge, q₀, has to be zero for no electrostatic forcehaving an equation where k and q₀ can be divided out of the equation will allow us to solve for q₃ $\begin{aligned} f_{net} & = 0\\ f_{01} + f_{02} + f_{03} & = 0 \\ \dfrac{kq_0q_1}{(\text{6.0 m})^2} + \dfrac{kq_0q_2}{(\text{15 m})^2} + \dfrac{kq_0q_3}{(\text{26 m})^2} & = 0 \\ kq_0 \left( \dfrac{q_1}{(\text{6.0 m})^2} + \dfrac{q_2}{(\text{15 m})^2} + \dfrac{q_3}{(\text{26 m})^2}\right) & = 0 \\ \dfrac{q_1}{(\text{6.0 m})^2} + \dfrac{q_2}{(\text{15 m})^2} + \dfrac{q_3}{(\text{26 m})^2} & = 0 \end{aligned}$ isolating: $\begin{aligned} \dfrac{q_3}{(\text{26 m})^2} & = -\dfrac{q_1}{(\text{6.0 m})^2} - \dfrac{q_2}{(\text{15 m})^2} \\ q_3 & = -(\text{26 m})^2\left(\dfrac{q_1}{(\text{6.0 m})^2} + \dfrac{q_2}{(\text{15 m})^2}\right) \\ q_3 & = -(\text{26 m})^2\left(\dfrac{6.0\times10^{-6} \text{ c}}{(\text{6.0 m})^2} + \dfrac{-4.0\times10^{-6} \text{ c}}{(\text{15 m})^2}\right) \\ q_3 & = -1.0064888 \times 10^{-4}\text{ c} \\ q_3 & = -1.0\times 10^{-4}\text{ c} \end{aligned}$ a charge of -1.0 × 10⁻⁴ c must be placed at x = 26 m.the sign of the charge will be the same as the -4.0 µc charge

Another question on Physics

Physics, 21.06.2019 19:40

Anne applies a force on a toy car and makes it move forward. what can be said about the forces acting on the toy car at the moment anne applies the force?

Answers: 3

Answer

Physics, 21.06.2019 22:50

Aplane takes off from an airport and flies to town a, located d1 = 215 km from the airport in the direction 20.0° north of east. the plane then flies to town b, located d2 = 230 km at 30.0° west of north from town a. use graphical methods to determine the distance and direction from town b to the airport. (enter the distance in km and the direction in degrees south of west.)

Answers: 2

Answer

Physics, 21.06.2019 23:30

Which lists the main components of darwin’s theory of evolution? a. random mutations drive evolution; the evolution of a population happens slowly; organisms have common ancestors; organisms do not change. b. natural selection drives evolution; the evolution of a population happens slowly; organisms have common ancestors; organisms change over time. c. natural selection drives evolution; the evolution of a population happens rapidly; organisms have common ancestors; organisms change over time. d. random mutations drive evolution; the evolution of a population happens rapidly; organisms have common ancestors; organisms do not change.

Answers: 1

Answer

Physics, 22.06.2019 10:10

What is the angular momentum of the bar about the axle?

Answers: 3

Answer

You know the right answer?

Idk>?
...

Questions