subject

Physics, 02.11.2020 19:30 davidsouth444

I WILL GIVE BRAINLIEST Carlos uses a machine to decrease his force. Which of the following statements is true?

His machine must decrease the distance the object moves.

His machine must increase the distance the object moves.

His total amount of work has decreased.

ansver

Answers: 2

Show answers

Another question on Physics

question

Physics, 21.06.2019 21:30

Look at the potential energy diagram for a chemical reaction. which statement correctly describes the energy changes that occur in the forward reaction?

Answers: 1

question

Physics, 22.06.2019 02:30

Aforce of 9.00 newtons acts at an angle of 19.0 to the horizontal. what is its component in the horizontal direction?

Answers: 2

question

Physics, 22.06.2019 18:00

Astudent weighing 700 n climbs at constant speed to the top of an 8 m vertical rope in 10 s. the average power expended by the student to overcome gravity is most nearly

Answers: 2

question

Physics, 22.06.2019 22:00

Aviolently rotating column of air is formed around a region of extremely low air pressure above land. which of these weather conditions is most likely to follow? blizzard cyclone tornado hurricane

Answers: 1

You know the right answer?

I WILL GIVE BRAINLIEST Carlos uses a machine to decrease his force. Which of the following statemen...

Questions

question

Chemistry, 14.09.2019 00:20

Asample of coal has the following analysis (wt %). moisture 1.1%, fixed carbon 74%, volatile matter 17.9%, carbon 63.7%, hydrogen 3.3%, nitrogen 1.7%,...

question

History, 14.09.2019 00:20

Why was it important to say that “all men” were "created equal"? choose the best answer....

question

Engineering, 14.09.2019 00:20

List some of the performance requirements for a bottle opener....

question

Engineering, 14.09.2019 00:20

In addition to the shaping requirement, what additional reason might you have for excluding the glass rod from consideration?...

question

Engineering, 14.09.2019 00:20

For this particular design scenario, one consideration is that a shaping operation of some type must be applied to the straight rods in order to make...

question

Engineering, 14.09.2019 00:20

Agas turbine receives a mixture having the following molar analysis: 10% co2, 19% h2o, 71% n2 at 720 k, 0.35 mpa and a volumetric flow rate of 3.2 m3...

question

Engineering, 14.09.2019 00:20

A(100) silicon wafer is 700 um thick. a rectangular mask with unknown size is used to pattern the wafer before through-wafer etch. the sides of the ma...

question

Engineering, 14.09.2019 00:20

An ideal vapor compression refrigeration cycle that uses refrigerant-134a as its working fluid maintains a condenser at 1000 kpa and the evaporator at...

question

Engineering, 14.09.2019 00:20

Arefrigerator uses refrigerant-134a as the working fluid and operates on an ideal vapor-compression refrigeration cycle between 0.12 and 0.7 mpa. the...

question

Engineering, 14.09.2019 00:20

A250mm wide and 25mm thick plate is to be reduced in a single pass in a 2-high rolling mill to final thickness of 20mm. the roll has a radius of 250mm...

question

Engineering, 14.09.2019 00:20

(a) calculate the ratio of the maximum radial stresses at the edge and centre of a flat circular steel plate clamped at its periphery and subjected to...

question

Engineering, 14.09.2019 00:20

Acircular thin steel diaphragm having an effective diameter of 200 mm is clamped around its periphery and is subjected to a uniform gas pressure of 18...

question

Engineering, 14.09.2019 00:20

What other material properties should be considered for this application, and which of the provided materials would be suitable candidates for conside...

question

Engineering, 14.09.2019 00:20

An ideal vapor compression refrigeration cycle operates at steady state with refrigerant 134a as the working fluid. saturated vapor enters the compres...

question

Engineering, 14.09.2019 00:20

Determine the specific volume of superheated water vapor at 15 mpa and 1000c, using (a) the ideal-gas equation, and (b) the steam tables....

question

Engineering, 14.09.2019 00:20

Two litres of hot liquid at 80°c are poured into a container of mass 0.8 kg, which is at 15°c. determine the equilibrium temperature if no external he...

question

Engineering, 14.09.2019 00:20

Find the value of h for refrigerant-134a when p = 0.30 mpa and s = 1.0023. h = kj/kg....

question

Engineering, 14.09.2019 00:20

Awindow air conditioner unit is placed on a laboratory bench and tested in cooling mode using 750 w of electric power with a cop of 1.75. what is the...

question

Engineering, 14.09.2019 00:20

One kilogram of ice at -5°c is mixed with 2 kg of water at 18°c in an insulated copper vessel of mass 1.5 kg. at equilibrium, the vessel contains both...

question

Engineering, 14.09.2019 00:20

Determine the maximum possible efficiency of the following heat engines: (a) an internal-combustion engine using the atmosphere at 20°c as the heat s...

More questions: Physics Another questions