subject
Physics, 04.09.2020 21:01 maciemarklin3032

What is the slope of the line plotted below?


What is the slope of the line plotted below?

ansver
Answers: 2

Another question on Physics

question
Physics, 22.06.2019 14:30
Exercise 2. find the wavelength of a photon emitted when an electron jumps from the n = 3 energy level down to the n = 2 energy level. where is this photon in the electromagnetic spectrum?
Answers: 3
question
Physics, 23.06.2019 02:50
Aweather balloon has a volume of 52.5 liters at a temperature of 252 k. the balloon is released and rises to an altitude where the temperature is 295 k. how does this temperature change affect the gas particle motion?
Answers: 1
question
Physics, 23.06.2019 06:00
The precision of a voltmeter is ±0.005 v. the accepted value for a measurement is 9.016 v. which measurement is in the accepted range? 9.005 v 9.006 v 9.018 v 9.025 v
Answers: 1
question
Physics, 23.06.2019 08:30
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
You know the right answer?
What is the slope of the line plotted below?
...
Questions
question
Mathematics, 09.09.2021 14:00
question
Mathematics, 09.09.2021 14:00
question
Mathematics, 09.09.2021 14:00
question
English, 09.09.2021 14:00
question
Computers and Technology, 09.09.2021 14:00
question
Mathematics, 09.09.2021 14:00
question
Mathematics, 09.09.2021 14:00