Physics, 01.07.2020 22:01 adriandehoyos1p3hpwc
10) If the distance between the center of the ball and the center of the target is less than the sum of the radius of the ball and the radius of the target, then explain how come that means the two have collided. Draw a picture if it helps your explanation.
Answers: 1
Physics, 21.06.2019 13:10
Abox is pushed down at an angle of 32 degrees on a rough surface. the box moves to the right.what equation should be used to find the net force in the y-direction? answers: a. fnet,y = fn - fgb. fnet,y= fp - ffc. fnet,y = fn-fg- fpcos(32)d. fnet,y = fn-fg-fpsin(32)
Answers: 2
Physics, 21.06.2019 19:30
Is it possible to use the energy from two atoms colliding to create a clean burning lasting fuel source with a large amount of force? is it also possible to harness that energy from the two atoms colliding to create a clean energy source that will last for years from just two atoms colliding. is there a possibility to control and store that energy for years but slowly let the energy out enough to power cities cheaper and faster.
Answers: 3
Physics, 23.06.2019 08:30
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
Physics, 23.06.2019 09:00
Choose the correct general statement concerning the total potential and kinetic energy at any point along the arc of swing. the total energy at any point along the arc of swing of the pendulum is always less than 12 joules. the total energy at any point along the arc of swing of the pendulum is always more than 12 joules. the total energy at any point along the arc of swing of the pendulum is always equal to 12 joules. not enough information to determine
Answers: 1
10) If the distance between the center of the ball and the center of the target is less than the sum...
Health, 17.03.2021 23:40
Mathematics, 17.03.2021 23:40
English, 17.03.2021 23:40
Computers and Technology, 17.03.2021 23:40
Social Studies, 17.03.2021 23:40
Mathematics, 17.03.2021 23:40
Mathematics, 17.03.2021 23:40
English, 17.03.2021 23:40
Mathematics, 17.03.2021 23:40
Health, 17.03.2021 23:40
Mathematics, 17.03.2021 23:40
Mathematics, 17.03.2021 23:40