Physics, 03.03.2020 17:29 netflixacc0107

Which formula is used to calculate average velocity?

V Subscript a v g Baseline = StartFraction x Subscript f Baseline minus x Subscript I Baseline over t Subscript f Baseline minus t Subscript i Baseline EndFraction
V Subscript a v g Baseline = StartFraction t Subscript f Baseline minus t sub I over x sub f minus x sub I
v Subscript a v g Baseline = StartFraction d over t EndFraction
v Subscript a v g Baseline = StartFraction t over d EndFraction

Answers: 2

Show answers

Another question on Physics

Physics, 22.06.2019 16:30

When measuring volume, why is it important to use the correct tools and units to attain the greatest accuracy? use specific examples from the lab to support your answer. (5 points)

Answers: 1

Answer

Physics, 22.06.2019 20:30

Light from two different sources are incident upon the same side of a polarizing filter. light from one source is polarized with total intensity ip, while light from the other source is unpolarized with total intensity iu. as you rotate the polarizing filter through 360 degrees, the intensity of the transmitted light on the other side varies by a factor of 9. what is the relative intensity of the initial polarized source to the unpolarized source, or ip/iu?

Answers: 2

Answer

Physics, 22.06.2019 22:30

Use the drop-down menus to answer each question. which line represents the movement of a cart with a constant acceleration? a which line represents the movement of a cart with a constant velocity? c which lines represents a cart with no velocity or acceleration? b

Answers: 1

Answer

Physics, 23.06.2019 08:30

Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28

Answers: 2

Answer

You know the right answer?

Which formula is used to calculate average velocity?

V Subscript a v g Baseline = StartF...

Questions