Physics, 21.06.2019 23:10 itzlianne

A248-g piece of copper is dropped into 390 ml of water at 22.6 °c. the final temperature of the water was measured as 39.9 °c. calculate the initial temperature of the piece of copper. assume that all heat transfer occurs between the copper and the water. remember, the density of water is 1.0 g/m

Answers: 1

Show answers

Another question on Physics

Physics, 22.06.2019 01:30

For problems 1-3, consider a simple dc brush motor with a permanent magnet stator. with an an consider a simple dc brush motor with a permanent magnet ae supply voltage of 100 v, the no-load speed of the motor is 1000 rpm. this motor can provide a torque of 1.9 n-m at 800 rpm drawing a current of 2 a current are both zero at no load.) 1. with an armature supply voltage of 100 v, the motor is operated at 900 rpm. what is the motor torque? what is the mechanical power delivered by the motor? what is the current draw? what is the electrical power input? what is the energy efficiency of the motor? with an armature supply voltage of 100 v, the motor is operated at 1100 rpm (where it acts as a generator). what torque input is required? what mechanical power is required what current is generated? what is the electrical power generated? what is the energy efficiency of the motor acting as a generator? 2. with an armature supply voltage raised to 120 v, the motor is operated at 1000 rpm. what is the no-load speed? what is the motor torque? what is the mechanical power delivered by the motor? what is the current draw? what is the electrical power input what is the energy efficiency of the motor? 3.

Answers: 3

Answer

Physics, 22.06.2019 05:30

Thomas his older brothers, who own a junk yard, on the weekends to earn extra money. he likes to them push broken-down cars to the back of the junk yard because it makes him feel strong. last saturday, they pushed three cars with different weights, and he noticed he used different amounts of force for each one. the cars were the following weights: white car: 2,700 kg red car: 1,500 kg blue car: 2,100 kg think about how much force is needed to move each car. which correctly lists the cars in order from the most to least amount of force needed to move them? a) white, blue, red b) blue, red, white c) red, white, blue d) white, red, blue

Answers: 2

Answer

Physics, 22.06.2019 06:30

5submission this assignment is worth 20 points total. you are required to submit the following by next lab: 1. (3 points) determine the equation for the output angular velocity ω2 = θ˙ 2 as a function of θ1, ω1 = θ˙ 1 and α. you must show all your work to receive credit. 2. (2 points) use the result of problem#1 to plot ω2 over 0 ≤ θ1 ≤ 360deg with ω1 = 360deg/sec. do this for α = {10,30}deg. show the results on the same plot and properly label the axes, title, legend. for this you can use matlab or ms excel. 3. (3 points) determine the equation for the output angular acceleration ω˙ 2 and create a plot similar to the one in problem#2. 4. (10 points) submit plots of the results (ω2 and ω˙ 2) obtained from creo/mechanism and compare them to results of problem#2 and problem#3. note that you should do these comparisons for the two cases with α = {10,30}deg. 5. (2 points) provide a brief explanation of the results. did they match? what are the implications as misalignment angle increases?

Answers: 3

Answer

Physics, 22.06.2019 16:00

Which composition of water moves to begin a deepwater current?

Answers: 2

Answer

You know the right answer?

A248-g piece of copper is dropped into 390 ml of water at 22.6 °c. the final temperature of the wate...

Questions