subject

Mathematics, 05.07.2021 16:30 goargrant

I need help anybody know this

I need help anybody know this

ansver

Answers: 1

Show answers

Another question on Mathematics

question

Mathematics, 21.06.2019 21:30

How do your peer relationships affect your overall health status? what can you do to improve your peer relationships?

Answers: 1

question

Mathematics, 21.06.2019 22:00

Uestion 1(multiple choice worth 5 points) (05.02)alex wants to paint one side of his skateboard ramp with glow-in-the-dark paint, but he needs to know how much area he is painting. calculate the area of the isosceles trapezoid. isosceles trapezoid with top base 12 feet, bottom base of 18 feet, and height of 6 feet. 72 ft2 84 ft2 90 ft2 108 ft2

Answers: 1

question

Mathematics, 21.06.2019 23:30

Which term applies to agb and dge? a. obtuse b. supplementary c. complementary d. vertical

Answers: 1

question

Mathematics, 22.06.2019 02:00

Point a is at 12, and point d is at 56. point c is midway between a and d, and point b is midway between a and c. which of these is the coordinate of b?

Answers: 3

You know the right answer?

I need help anybody know this
...

Questions

question

Engineering, 11.07.2019 05:10

What size (inner diameter) of concrete pipe (with e-0.005) is required to carry water (at 60°f) at a discharge rate of 15 ft3/s and with a head loss o...

question

Engineering, 11.07.2019 05:10

Water if flowing steadily in a 0.6-m wide rectangular open channel at a rate of 0.3 m^3/s. if the depth is 0.15 m, a)-determine i) the flow velocity,...

question

Engineering, 11.07.2019 05:10

An elevated water tower is used to supply water to a city. to make water available at a pressure of 400 kpa at a ground level location within the city...

question

Engineering, 11.07.2019 05:10

What is considered a uselapplication of modal analysis? (1) identifying the rigid body modes (2) finding modal frequencies (3) obtaining the modal am...

question

Engineering, 11.07.2019 05:10

Arefrigeration cycle rejects qn 500 btu/s to a hot reservoir at 540 r, while receiving c200 btu/s at 240°r. this refrigeration cycle a)- is internally...

question

Engineering, 11.07.2019 05:10

Acylindrical specimen of some metal alloy having an elastic modulus of 117 gpa and an original cross-sectional diameter of 3.6 mm will experience only...

question

Engineering, 11.07.2019 05:10

Arigid, insulated tank that is initially evacuated is connected through a valve to a supply line that carries steam at 3.5 mpa. now the valve is opene...

question

Engineering, 11.07.2019 05:10

Aheat pump, using ammonia as the refrigerant, has the following conditions , heat effect 75,000kj/sec , evaporator pressure 0.22mpa , condenser pressu...

question

Engineering, 11.07.2019 05:10

A2.5 cm diameter horizontal water jet with a speed of vi- 40 m/s relative to the ground is deflected by a 60° stationary cone whose base diameter is 2...

question

Engineering, 11.07.2019 05:10

For a specified inlet state, exit pressure and mass flowrate, the power input of a that of an compressor operating adiabatically and at steady state w...

question

Engineering, 11.07.2019 05:10

Asingle-cylinder four-stroke-cycle spark- ignition engine has a bsfc of 0.4 kg/kw-hr and a volumetric efficiency of 78% at a speed of 45 rps. the bore...

question

Engineering, 11.07.2019 05:10

Heat in the amount of 100 kj is transferred directly from a hot reservoir at 1200 k to a cold reservoir at 600k. calculate the entropy change of the t...

question

Engineering, 11.07.2019 05:10

A1m by 1m square gate is to be located on one vertical side of a tank that will contain 2 m depth of water up to the bottom of the gate. determine the...

question

Engineering, 11.07.2019 05:10

Acylindrical metal specimen having an original diameter of 11.80 mm and gauge length of 51.7 mm is pulled in tension until fracture occurs. the diamet...

question

Engineering, 11.07.2019 05:10

Air is compressed in an isentropic process from an initial pressure and temperature of p1 = 90 kpa and t1=22°c to a final pressure of p2=900 kpa. dete...

question

Engineering, 11.07.2019 05:10

Is a process that is internally reversible and adiabatic necessarily isentropic? explain using an equation....

question

Engineering, 11.07.2019 05:10

After the formation of cells is finished, a cellular manufacturing system can use either a decoupling or an integrating approach to manage the materia...

question

Engineering, 11.07.2019 05:10

Apipe system consists of a lower section with two 90° elbows and an upper section with a 180° bend and two straight flow tees. if the flow is measured...

question

Physics, 11.07.2019 05:10

Asled of mass m is being pulled horizontally by a constant horizontal force of magnitude f. the coefficient of kinetic friction is μk. during time int...

question

Engineering, 11.07.2019 05:10

What is analogous to the convection coefficient in structural analysis? (1)-prescribed displacement (2)-prescribed stress (3)-damping coeffcient (4)-...

More questions: Mathematics Another questions