Mathematics, 29.04.2021 20:50 chunkymonkey090

Yes it is possible for a number to have factorization , because 1 is not a prime number or composite do i agree or disagree with this.

Answers: 2

Show answers

Answers

The only factor of 1 is 1. A prime number has exactly two factors so 1 isn't prime. A composite number has more than 2 factors, so 1 isn't composite.

if this helped subscribe to Amiredagoat Yt

Step-by-step explanation:

Answer from: jazzy9438

Yes, 1 is not prime nor composite

Step-by-step explanation:

Answer from: Quest

the length of o'p' is $1.5\times op$ .

step-by-step explanation:

it is given that the quadrilateral m'n'o'p' is the image of quadrilateral mnop after dilation.

the center of dilation is origin and the scale factor is 1.5.

in dilation the image and preimge are similar figures. it means the sides of image and preimage are proportional.

the scale factor is defined as

$k=\frac{o'p'}{op}$

the scale factor is 1.5.

$1.5=\frac{o'p'}{op}$

multiply both sides by op.

$1.5\times op=o'p'$

note: if the value of op is given, then multiply the value of op with 1.5 to get the length of side o'p'.

therefore length of o'p' is $1.5\times op$ .

Answer from: Quest

answer: e 9, 5.75

step-by-step explanation:

step 1

find the variation ab in the x coordinate

delta x=(x2-x1)=10-> 8 units

find the variation ab in the y coordinate

delta y=(y2-y1)=6-> 2 units

step 2

find the coordinates point c

x coordinate

cx=ax+delta x*2/> cx=2+8*(2/> cx=3

y coordinate

cy=ay+delta y*2/> cy=4+2*(2/> cy=4.25

the coordinates of point c are (3,4.25)

step 3

find the coordinates point d

x coordinate

dx=ax+delta x*4/> dx=2+8*(4/> dx=4

y coordinate

dy=ay+delta y*4/> dy=4+2*(4/> dy=4.5

the coordinates of point d are (4, 4.5)

step 4

find the coordinates point e

x coordinate

ex=ax+delta x*4/> ex=2+8*(6/> ex=5

y coordinate

ey=ay+delta y*4/> ey=4+2*(6/> ey=4.75

the coordinates of point e are (5, 4.75)

step 5

find the coordinates point f

x coordinate

fx=ax+delta x*4/> fx=2+8*(8/> fx=6

y coordinate

fy=ay+delta y*4/> fy=4+2*(8/> fy=5

the coordinates of point f are (6,5)

step 6

find the coordinates point g

x coordinate

gx=ax+delta x*4/> gx=2+8*(10/> gx=7

y coordinate

gy=ay+delta y*4/> gy=4+2*(10/> gy=5.25

the coordinates of point g are (7,5.25)

step 7

find the coordinates point h

x coordinate

hx=ax+delta x*4/> hx=2+8*(12/> hx=8

y coordinate

hy=ay+delta y*4/> hy=4+2*(12/> hy=5.5

the coordinates of point h are (8,5.5)

step 8

find the coordinates point i

x coordinate

ix=ax+delta x*4/> ix=2+8*(14/> ix=9

y coordinate

iy=ay+delta y*4/> iy=4+2*(14/> iy=5.75

the coordinates of point i are (9,5.75)

- r3ktforgood ☕

Another question on Mathematics

Mathematics, 21.06.2019 12:30

The polynomial function of least degree with a leading coefficient of 1 is: f(x) = x3 + ax2 + bx + c

Answers: 1

Answer

Mathematics, 21.06.2019 16:30

Refer to the table below if needed. second quadrant third quadrant fourth quadrant sin(1800- - cos(180° -) tan(180°-e) =- tane cot(1800-0) 10 it to solo 888 sin(180° +c) = - sine cos(180° +) =- cose tan(180° +c) = tane cot(180° +o) = cote sec(180° + c) = - seco csc(180° +2) = - csce sin(360° -) =- sine cos(360° -) = cose tan(360° - e) =- tane cot(360° -) = -cote sec(360° -) = seco csc(360° -) = csco sec(180° -) = csc(180° -) = csca 1991 given that sine = 3/5 and lies in quadrant ii, find the following value. tane

Answers: 2

Answer

Mathematics, 21.06.2019 21:20

The edge of a cube was found to be 30 cm with a possible error in measurement of 0.4 cm. use differentials to estimate the maximum possible error, relative error, and percentage error in computing the volume of the cube and the surface area of the cube. (round your answers to four decimal places.) (a) the volume of the cube maximum possible error cm3 relative error percentage error % (b) the surface area of the cube maximum possible error cm2 relative error percentage error %

Answers: 3

Answer

Mathematics, 21.06.2019 22:30

Amachine that produces a special type of transistor (a component of computers) has a 2% defective rate. the production is considered a random process where each transistor is independent of the others. (a) what is the probability that the 10th transistor produced is the first with a defect? (b) what is the probability that the machine produces no defective transistors in a batch of 100? (c) on average, how many transistors would you expect to be produced before the first with a defect? what is the standard deviation? (d) another machine that also produces transistors has a 5% defective rate where each transistor is produced independent of the others. on average how many transistors would you expect to be produced with this machine before the first with a defect? what is the standard deviation? (e) based on your answers to parts (c) and (d), how does increasing the probability of an event aâ†µect the mean and standard deviation of the wait time until success?

Answers: 3

Answer

You know the right answer?

Yes it is possible for a number to have factorization , because 1 is not a prime number or composite...

Questions