Question 11 pts Which of the following statements best describes a physical property?
Group of answer choices

when a substance reacts to form an entirely new substance with new properties

when two substances bond together to form a new substance with similar properties

when a substance undergoes a change to its chemical makeup, but does not change its physical appearance

can be measured or observed without matter changing to an entirely different substance

Flag this Question
Question 21 pts
Which of the following is NOT an example of a physical property?
Group of answer choices

density

pH

conductivity

boiling point

Flag this Question
Question 31 pts
Which of the following statements is accurate based on the table?

Solute Grams of Solute that Will Dissolve in 0.5 L of Water (20 °C)
Baking Soda 48
Epsom salt 125
Table salt 180
Table sugar 1000
Group of answer choices

Water is a solvent

Baksing Soda, Epsom Salt and Table Salt is a solvent

Baking Soda, Epsom salt, table salt and table sugar are solvents

Water is a solute

Flag this Question
Question 41 pts
Which of the following most likely speeds up the rate at which something dissolves?
Group of answer choices

mixing, hot temperatures and larger particle size

mixing, cold temperatures and larger particle size

mixing, hot temperatures and smaller particle size

mixing, cold temperatures and smaller particle size

the 3rd one

Step-by-step explanation:

i need points

Step-by-step explanation:

AWA

part a

answer: a reasonable domain is where n is a real number. so n can be between 0 and 10. both endpoints are included.

work shown:

n is the number of days after the experiment starts. the smallest n can be is n = 0 which means that 0 days have gone by, and we're at the start. to find out how large n should be, then replace f(n) with 16.13 and solve for n. use logarithms to isolate the exponent.

f(n) = 12*(1.03)^n

16.13 = 12*(1.03)^n

16.13/12 = (1.03)^n

1.34416666666667 = (1.03)^n

(1.03)^n = 1.34416666666667

log[ (1.03)^n ] = log[ 1.34416666666667 ]

n*log[ 1.03 ] = log[ 1.34416666666667 ]

n = log[ 1.34416666666667 ]/log[ 1.03 ]

n = 10.0062999823929

this rounds to n = 10 which is fairly close but not 100% perfect. so this is the largest n can be.

note: if you plug n = 10 into f(n), you'll get roughly 16.127 which rounds to 16.13 (this comes up again in part c)

=====================================

part b

answer: the y intercept is 12. it represents the starting height of the plant in cm.

work shown:

plug n = 0 into the f(n) function. simplify

f(n) = 12*(1.03)^n

f(0) = 12*(1.03)^0

f(0) = 12*(1)

f(0) = 12

on day n = 0, aka the starting point, the height f(n) is 12 cm

=====================================

part c

answer: the average rate of change is approximately 0.43061036458991 (round however you need to). this represents the average growth rate from day n = 3 to day n = 10. so the plant grew roughly 0.43 cm per day during this timespan, assuming you round to 2 decimal places.

work shown:

compute f(3)

f(n) = 12*(1.03)^n

f(3) = 12*(1.03)^3

f(3) = 13.112724 < we'll use this later

compute f(10)

f(n) = 12*(1.03)^n

f(10) = 12*(1.03)^10

f(10) = 16.1269965521294 < we'll use this later

now use the formula below with a = 3 and b = 10

aroc = average rate of change

aroc = [ f(b) - f(a) ]/[ b - a ]

aroc = [ f(10) - f(3) ]/[ 10 - 3 ]

aroc = (16.1269965521294 - 13.112724)/(10 - 3)

aroc = 3.0142725521294/7

aroc = 0.43061036458991

round this however you need to

note: the plant grew approximately 3.01 cm over 7 days, so roughly 0.43 cm per day is the average growth rate (if you were to round to 2 decimal places).