Consider the following computer output for an experiment to test effect of factor treatments and blocks. Use alpha = 0.05. Analysis of Variance Source of Variance df SS MS F P-value Factor ? 126 63 ? ? Block ? 54 18 ? ? Error 6 ? 2.8 Total 11 197 1) Find the degree of freedom for the factor and the block. (2 pts) 2) Find the number of levels of the factor and the number of blocks used in this experiment. (2 pts) 3) Estimate the P-value for the F-statistic of the factor. (2 pts) 4) Estimate the variance of the error term, sigma square hat. (2 pts) 5) Since the P-value for the F-statistic of the block is less than alpha = 0.05, there is no effect of the block in this experiment. True or False. (2 pts)

Table 2.2: Differences in runstitching times (standard − ergonomic).

1.03 -.04 .26 .30 -.97 .04 -.57 1.75 .01 .42

.45 -.80 .39 .25 .18 .95 -.18 .71 .42 .43

-.48 -1.08 -.57 1.10 .27 -.45 .62 .21 -.21 .82

A paired t-test is the standard procedure for testing this null hypothesis.

We use a paired t-test because each worker was measured twice, once for Paired t-test for

each workplace, so the observations on the two workplaces are dependent. paired data

Fast workers are probably fast for both workplaces, and slow workers are

slow for both. Thus what we do is compute the difference (standard − er-

gonomic) for each worker, and test the null hypothesis that the average of

these differences is zero using a one sample t-test on the differences.

Table 2.2 gives the differences between standard and ergonomic times.

Recall the setup for a one sample t-test. Let d1, d2, . . ., dn be the n differ-

ences in the sample. We assume that these differences are independent sam-

ples from a normal distribution with mean µ and variance σ

2

, both unknown.

Our null hypothesis is that the mean µ equals prespecified value µ0 = 0

(H0 : µ = µ0 = 0), and our alternative is H1 : µ > 0 because we expect the

workers to be faster in the ergonomic workplace.

The formula for a one sample t-test is

t =

¯d − µ0

s/√

n

,

where ¯d is the mean of the data (here the differences d1, d2, . . ., dn), n is the The paired t-test

sample size, and s is the sample standard deviation (of the differences)

s =

vuut

1

n − 1

Xn

i=1

(di − ¯d )

2 .

If our null hypothesis is correct and our assumptions are true, then the t-

statistic follows a t-distribution with n − 1 degrees of freedom.

The p-value for a test is the probability, assuming that the null hypothesis

is true, of observing a test statistic as extreme or more extreme than the one The p-value

we did observe. “Extreme” means away from the the null hypothesis towards

the alternative hypothesis. Our alternative here is that the true average is

larger than the null hypothesis value, so larger values of the test statistic are

extreme. Thus the p-value is the area under the t-curve with n − 1 degrees of

freedom from the observed t-value to the right. (If the alternative had been

µ < µ0, then the p-value is the area under the curve to the left of our test

Step-by-step explanation: Through the laid down FORMULA ABOVE

the answer is thin because within context, the stanza concludes the and frail tone the people have toward each other, and the fact that it would be thin, makes the most sense compared to "pliable" or "not hard or firm to the touch". hope this , good luck.

step-by-step explanation:

can i have brainliest