subject
Mathematics, 04.12.2019 19:31 Kurlyash

Examine the power.
1. identify the base:
2. determine the exponent:
3. write in expanded form:
what is the value of the power?

ansver
Answers: 3
Show answers

Another question on Mathematics

question
Mathematics, 21.06.2019 17:30
What is the greater volume 72 quarts or 23 gallons
Answers: 1
Answer
question
Mathematics, 21.06.2019 18:30
Complex numbers multiply √-4 * √-25 and show all intermediate steps. alternative notation is sqrt(-4) * sqrt(-25).
Answers: 1
Answer
question
Mathematics, 21.06.2019 18:30
What are different types of statistical programs
Answers: 2
Answer
question
Mathematics, 21.06.2019 19:30
Me. i can't figure out this question. give an explanation too. .
Answers: 1
Answer
You know the right answer?
Examine the power.
1. identify the base:
2. determine the exponent:
3. write in...
Questions
question
Mathematics, 26.07.2019 16:20
Type the correct answer in each box. use numerals instead of words. if necessary, use / for the fraction bar. zoe is shopping for a new car and has to...
question
Engineering, 26.07.2019 16:20
Water is the working fluid in a rankine cycle. steam enters the turbine at 1400 lbf/in^2 and 1000 degrees f. the condenser pressure is 2 lbf/in^2. bot...
question
Engineering, 26.07.2019 16:20
Which of the following dimensionless numbers govern the transition turbulent flow in an external forced convection analysis? numbers govern the trans...
question
Engineering, 26.07.2019 16:20
Put the four main steps of the injection molding process in correct order. (place the correct step number after the text line) a)- injection of plasti...
question
Engineering, 26.07.2019 16:20
Which dimensionless number can describe the rela boundary layers? umber can describe the relative thickness of the velocity and thermal a. biot b. nu...
question
Engineering, 26.07.2019 16:20
A½ inch diameter bolt is under a shear load of 4500 lb. determine the average shear stress on the bolt. assume the bolt is in single shear and is made...
question
Engineering, 26.07.2019 16:20
The pressure drop is the irreversible pressure loss between the inlet and the exit of a tube bank. a pressure loss has units of a. j 1 b. n c. pa d. w...
question
Engineering, 26.07.2019 16:20
What does the 13 in the ½-13 screw call-out stand for? a. thread pitch (distance between threads) b. major diameter of thread c. threads per inch d....
question
Engineering, 26.07.2019 16:20
The diesel cycle is very close to the otto cycle. what is a difference between the two air-standard cycles? a)-the diesel cycle assumes constant volu...
question
Engineering, 26.07.2019 16:20
One can expect the velocity boundary layer for laminar flow to be much thicker than the thermal boundary layer when the prandtl number is a. > >...
question
Engineering, 26.07.2019 16:20
Select a light w shape for a column subjected to an axial compressive load of 355 kips. the unbraced length of column is 16 ft and the ends are pinned...
question
Engineering, 26.07.2019 16:20
Which has more threads per inch: ¼-20 or an m8-1? a)- ¼-20 b)- м8-1 c)- same...
question
Engineering, 26.07.2019 16:20
Use the map of ohio that follows to find the average wind speed for columbus, ohio (5.5 m/s). a wind turbine located at byers mazda subaru near i 270...
question
Engineering, 26.07.2019 16:20
An a36 - 1.0 inch diameter steel tie rod is used to support a tensile load of 12,000 lb. determine the stress in the tie rod and calculate the factor...
question
Engineering, 26.07.2019 16:20
Afluid in direct contact direct contact with a stationary solid surface will have a velocity of zero in accordance with the condition. a. no-slip b. t...
question
Engineering, 26.07.2019 16:20
Steam enters an adiabatic turbine at 10 mpa and 500 °c and leaves at 30 kpa with a quality of 90 percent. neglecting the changes in kinetic and potent...
question
Engineering, 26.07.2019 16:20
Calculate the bending stress in a 1 ¾ in. x 12 in. x 18 ft. microllam lvl beam under the following load conditions: a)-2500 lb concentrated load at c...
question
Engineering, 26.07.2019 16:20
A) what is a free-cutting steel? explain. b) show the free energy vs. composition curve (schematic) for an alloy system a-b where there is a strong t...
question
Engineering, 26.07.2019 16:20
Acylindrical steel specimen is subjected to a stress of 100 mpa along the longitudinal axis. the undeformed specimen has a diameter do=10 mm and a len...
question
Engineering, 26.07.2019 16:20
What volume of helium is needed if a balloon is to lift a load of 1200kg (including the weight of the empty balloon)?...
More questions: Mathematics Another questions
See results (0)