subject
History, 15.11.2019 04:31 Lhuckabee

Fear of in strengthening fascism in

first blank:
a soviet invasion
economic instability
the government
a world war

second blank:
japan
italy
spain
the soviet union

ansver
Answers: 1
Show answers

Another question on History

question
History, 21.06.2019 14:30
From this passage, it is clear that president jackson believes the second bank of the united states
Answers: 1
Answer
question
History, 21.06.2019 22:30
What artifact did modern scholars study to them understand hieroglyphics
Answers: 1
Answer
question
History, 22.06.2019 00:00
Why were adams ideas not out into action
Answers: 1
Answer
question
History, 22.06.2019 01:00
Using the prompt, which ideas are most influenced by the petition of right? a) common law b) bill of rights c) divine right of kings d) declaration of independence
Answers: 1
Answer
You know the right answer?
Fear of in strengthening fascism in

first blank:
a soviet invasion
econo...
Questions
question
Biology, 26.07.2019 18:10
Atp is thermodynamically suited as a carrier of phosphoryl groups in animal cells because of all except a. it is intermediate in group-transfe...
question
Mathematics, 26.07.2019 18:10
< < 16 17 18 19 20 21 22 23 24 25 26 use the discriminant and se...
question
Engineering, 26.07.2019 18:10
Two large masses with mass moments of inertia i1, and i2, are fixed at either end of a uniform shaft with a length l and polar area moment of inertia...
question
Engineering, 26.07.2019 18:10
Obtain the natural frequencies and mode shapes for a free-free uniform beam in lateral vibration and plot the first three modes. ignore the rigid-body...
question
Engineering, 26.07.2019 18:10
An aluminum alloy has a specific energy of 0.3 hp-min/in3. what is the corresponding k, in n/mm^2...
question
Engineering, 26.07.2019 18:10
A20 mm deep slot is being milled in a block of aluminum with k 850 n/mm2. the tool is 25 mm in diameter, and has 2 teeth. it is rotating at 14,728 rpm...
question
Engineering, 26.07.2019 18:10
The turbines in hydroelectric plant are feed by water falling from a height of 100ft. assuming 95% efficiency for converting the potential energy to e...
question
Engineering, 26.07.2019 18:10
What is the difference between climb milling and conventional milling?...
question
Engineering, 26.07.2019 18:10
You are in a small boat on lake pueblo. the combined weight of you and the boat is 200lbf. the lake volume displaced by the boat is 72 ft^3. what is t...
question
Engineering, 26.07.2019 18:10
A50-mm-diameter ball is pressed against an identical ball of same material (e= 200 gpa) by a force of 500 n. calculate (a) the radius of the contact a...
question
Engineering, 26.07.2019 18:10
Asteel pipeline conveying gas has an internal diameter of 120 cm and an external diameter of 125 cm. it is laid across the bed of a river, completely...
question
Engineering, 26.07.2019 18:10
An initial surface flaw with a depth of 0.001 in is detected in a ferritic/pearlitic matter/anti-matter flux capacitor that makes temporal travel at w...
question
Engineering, 26.07.2019 18:10
Atitanium bar with specific energy of 3.0 w-s/mm3 is being turned from 50 mm diameter to 48 mm diameter over a length of 500 mm in 1 minute. how much...
question
Engineering, 26.07.2019 18:10
What is the most significant factors influencing crater wear?...
question
Engineering, 26.07.2019 18:10
A10-in. length of steel tubing (with properties of e =30 x 10^6psi v=0.3 and α=7x10^-6/ f° and q. cross-sectional area of 1 square in is installed wit...
question
Engineering, 26.07.2019 18:10
List 5 different mechanisms of tool wear?...
question
Engineering, 26.07.2019 18:10
Adiesel engine with a compression ratio of 16 has a cutoff ratio of 1.5. the state before polytropic compression (exponent 1.3) is 1700 cm3 , 96 kpa a...
question
Engineering, 26.07.2019 18:10
Design a variable stroke quick return mechanism with minimum stroke of 60mm and maximum of stroke of 270mm. let fixed link equals 75mm. the time ratio...
question
Engineering, 26.07.2019 18:10
Anew boat design is 30 m long and is designed to travel at 50 km/hr in the ocean. to test the design, it is decided to build a scale model operating i...
question
Engineering, 26.07.2019 18:10
Acantilever of length 0.5 m and square cross-section of sides 50 mm is subjected to a downward-acting alternating end load. the static tensileield s f...
More questions: History Another questions
See results (0)