![subject](/tpl/images/cats/User.png)
Engineering, 30.11.2021 22:10 jashaikamatuteowwp1p
What does it mean for one gear ratio to be “higher” than another, in terms of the turns of the pedal and turns of the wheels?
![ansver](/tpl/images/cats/User.png)
Answers: 2
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 03:10
What precautions should you take to prevent injuries when dealing with heavy loads?
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Apump is used to circulate hot water in a home heating system. water enters the well-insulated pump operating at steady state at a rate of 0.42 gal/min. the inlet pressure and temperature are 14.7 lbf/in.2, and 180°f, respectively; at the exit the pressure is 60 lbf/in.2 the pump requires 1/15 hp of power input. water can be modeled as an incompressible substance with constant density of 60.58 lb/ft3 and constant specific heat of 1 btu/lb or. neglecting kinetic and potential energy effects, determine the temperature change, in °r, as the water flows through the pump.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Refrigerant 134a enters an insulated compressor operating at steady state as saturated vapor at -26°c with a volumetric flow rate of 0.18 m3/s. refrigerant exits at 9 bar, 70°c. changes in kinetic and potential energy from inlet to exit can be ignored. determine the volumetric flow rate at the exit, in m3/s, and the compressor power, in kw.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
You know the right answer?
What does it mean for one gear ratio to be “higher” than another, in terms of the turns of the pedal...
Questions
![question](/tpl/images/cats/mat.png)
Mathematics, 21.02.2021 08:10
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 21.02.2021 08:10
![question](/tpl/images/cats/en.png)
English, 21.02.2021 08:10
![question](/tpl/images/cats/mat.png)
Mathematics, 21.02.2021 08:10
![question](/tpl/images/cats/istoriya.png)
History, 21.02.2021 08:10
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
English, 21.02.2021 08:10
![question](/tpl/images/cats/mat.png)
Mathematics, 21.02.2021 08:10
![question](/tpl/images/cats/mat.png)
Mathematics, 21.02.2021 08:10
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 21.02.2021 08:10
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 21.02.2021 08:10
![question](/tpl/images/cats/health.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 21.02.2021 08:10
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/en.png)
English, 21.02.2021 08:10
![question](/tpl/images/cats/informatica.png)
Computers and Technology, 21.02.2021 08:10
![question](/tpl/images/cats/mat.png)
Mathematics, 21.02.2021 08:10
![question](/tpl/images/cats/mat.png)
Mathematics, 21.02.2021 08:10