Engineering, 29.06.2021 07:30 dirttrackr75

1. advantages of 2 pulley system 2. disadvantages of 2 pulley system
3. advantages of 3 pulley system
4. disadvantages of 3 pulley system

Answers: 1

Show answers

Answers

Answer from: xelynncaldera

Advantages

The main advantage in the use of pulleys is that the effort becomes less as compared to the normal lifting of the weights. In other words, it reduces the amount of actual force required to lift heavy objects. It also changes the direction of the force applied. These two advantages in the use pulleys make them an important tool for heavy lifting. It also provides a mechanical advantage.

The other advantage in the use of pulleys is that the distance between the operator and weight. There is a safe distance between them which avoids any disaster. Pulleys are easy to assemble and cost-effective. The combination of different directional pulleys can change the position of the load with little effort. Though there are moving parts in the pulley system they require less or no lubrication after installation.

Disadvantages

Apart from the above-said advantages while using pulley systems, there are several disadvantages in their use. The main disadvantage in the use of the pulley system is that it requires large space to install and operate. The mechanical advantage of pulleys can go to higher values but need more space to install them.

In some cases, the ropes/belts move over the wheel with no grooves, the chances of the slip of ropes/belts from the wheel are inevitable. If the system is installed to use for a long time, they require maintenance and regular check-up of ropes/cables as the friction between the wheels and cables/ropes occur causing wear and tear to them. Continuous use of the system makes the ropes weak. The rope may break while using the system causing damages to the operator, surrounding place and the load which is being lifted.

Answer from: Quest

answer:

the army does care about its soilders sir i think yout getting off on the wrong foot sir you need to respect our country were keeping the peole that want to d harm towards you out. so dont go saying we don't care cause we do

Answer from: Quest

answer:

explanation:

it a unlucky day

Another question on Engineering

Engineering, 04.07.2019 18:10

Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Burgers vector is generally parallel to the dislocation line. a)-true b)-false

Answers: 2

Answer

Engineering, 04.07.2019 18:20

Find the minimum film thickness for a journal bearing with the data below. shaft diameter, d-50 mm, clearance ratio, cdratio? 0.001, shaft speed, n 2000 rpm; bearing length. i 200 mm; eccentricity ration, ? -0.55. ( note, cdratio-ca/d) the minimum film thickness is um

Answers: 2

Answer

You know the right answer?

1. advantages of 2 pulley system 2. disadvantages of 2 pulley system
3. advantages of 3 pulley...

Questions