subject
Engineering, 16.04.2021 19:30 naruto63

This is gonna be very long but I have no idea what to do, I'm confused. Course Project Part 4: Conducting the Experiment and Recording Data
After much preparation, you are finally ready to begin conducting your experiment. Due to all the hard work you put into your literature review and planning your procedures, the steps that you need to take to conduct your experiment successfully have already been set. While you conduct your experiment, you will need to keep a daily journal where you record the activities you undertake that are relevant to the experiment and also where you record any data that you collect. This is your experiment log and serves as a record of your work while also allowing you to make a record of any changes or modifications you may need to make during the experiment.

Conducting the Experiment and Keeping an Experiment Journal
Following the procedure that you established in the previous part of this project, set up your experiment and begin running it. Every day while your experiment is running you will make an entry in your journal. Record what activities you completed (refer to your outlined procedure to make sure you are following the procedure that you established), any modifications that had to be made to your set up or procedure, and any observations or data you collect. Even on days when you do not collect data (depending on your experiment, there may not be data collection every day), make an entry in your journal. Each journal entry should be clearly labeled with the date on which it was entered. You do not need to type up all your entries, but make sure that your journal entries are neatly written, as they will be evaluated by your instructor.

Depending on the topic and design of your experiment, the period of time during which you conduct and record your experiment may range from one to several weeks. In consultation with your instructor, you will establish a timeline for the evaluation of your journal. If you are running a shorter experiment, your journal may be evaluated several times over the course of one or two weeks. If your experiment takes longer to complete, you may have a weekly review over the course of a month. Follow the guidelines provided by your instructor.

Collecting Data
All experiments generate data. This data allows the scientist to evaluate the success of the experiment and make interpretations about the results generated by the investigation. When you record your data, you must collect it as consistently as possible. Returning to the plant experiment, it would be best to measure the plants on a set schedule. For example, you might choose to measure the plants every Thursday at 3 pm. It is important to measure the plants at the same time each week so that the difference in growth you might observe is a reflection of the experimental condition, not simply longer growing time. Additionally, it is important to use the same instruments to collect data. The plants should be measured with the same ruler or measuring tape each time. This helps reduce any error or bias that might be introduced by using different instruments to make measurements. Whatever measurements or data you collect, do so in a consistent manner. Use the same instruments, the same scales, and record the data in a standardized manner. It is also a good idea to record your experiment using photographs. This will help you later during analysis and provides information for others who might be interested in recreating your experiment. Record your data in your experiment journal, where it will be reviewed by your teacher on an on-going basis. Submit your journal to your instructor according to the schedule you have established together.

ansver
Answers: 2

Another question on Engineering

question
Engineering, 03.07.2019 23:20
Two technicians are discussing the intake air temperature (iat) sensor. technician a says that the computer uses the iat sensor as a backup to the engine coolant temperature (ect) sensor. technician b says that the powertrain control module (pcm) will subtract the calculated amount of fuel if the air measures hot. who is correct
Answers: 3
question
Engineering, 04.07.2019 18:10
Refrigerant 134a enters an insulated compressor operating at steady state as saturated vapor at -26°c with a volumetric flow rate of 0.18 m3/s. refrigerant exits at 9 bar, 70°c. changes in kinetic and potential energy from inlet to exit can be ignored. determine the volumetric flow rate at the exit, in m3/s, and the compressor power, in kw.
Answers: 1
question
Engineering, 04.07.2019 18:10
Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-cm-outer-diameter and 0.4-m-long tubes inside which the refrigerant is evaporating at -20°c. air approaches the tube bank in the normal direction at 0°c and 1 atm with a mean velocity of 4 m/s. the tubes are arranged in-line with longitudinal and transverse pitches of sl- st 1.5 cm. there are 30 rows in the flow direction with 15 tubes in each row. determine (a) the refrigeration capacity of this system and (b) pressure drop across the tube bank. evaluate the air properties at an assumed mean temperature of -5°c and 1 atm. is this a good assumption?
Answers: 1
question
Engineering, 04.07.2019 18:10
Afour cylinder four-stroke in-line engine has a stroke of 160mm, connecting rod length of 150mm, a reciprocating mass of 3kg and its firing order is 1-3-4-2. the spacing between cylinders is 100mm. i. show that the engine is in balance with regard to the primary inertia forces and primary 3. a and secondary inertia couples. li determine the out of balance secondary inertia force ii. propose ways of balancing this out of balance force and discuss the challenges that will arise
Answers: 3
You know the right answer?
This is gonna be very long but I have no idea what to do, I'm confused. Course Project Part 4: Cond...
Questions
question
Computers and Technology, 27.08.2019 04:50
question
Mathematics, 27.08.2019 04:50