Engineering, 12.03.2021 15:10 isamar7342

A. Determination of initial concentrations Volume of 0.25 M NaOH added (mL) 32.77
B. Determination of the Blank
Volume of 0.25 M NaOH added (mL) 5.30
C. Determination of Final Concentrations
Volume of 0.25 M NaOH added (mL) 14.384
(10pts) Calculations and Analysis
Use the data collected above and the given volumes of acetic acid and ethyl alcohol to determine the initial and equilibrium concentrations of acetic acid.
A. Determination of Initial Concentrations
Volume of 0.25 M NaOH added32.77 mL
(2pts) Initial concentration of acetic acid (M) Saved
B. Determination of the Blank
Volume of 0.25 M NaOH added5.30 mL
C. Determination of Final Concentrations
Volume of 0.25 M NaOH added14.38 mL
(4pts) Volume of 0.25 M required to neutralize acetic acid Saved
(4pts) Final concentration of acetic acid Saved
(8pts) D. Calculation of the Equilibrium Constant
Enter the equilibrium concentrations for all species and calculate the Keq for the reaction.
(1pts) Equilibrium concentration of acetic acid (from above) Saved
(1pts) Equilibrium concentration of ethyl alcohol Saved
(1pts) Equilibrium concentration of ethyl acetate
(1pts) Equilibrium concentration of water
(4pts) Value of Keq
Determination of an Equilibrium Constant
Are you completing this experiment online? Yes
A. Determination of initial concentrations
Volume of 0.25 M NaOH added (mL) 32.97
B. Determination of the Blank
Volume of 0.25 M NaOH added (mL) 5.43
C. Determination of Final Concentrations
Volume of 0.25 M NaOH added (mL) 14.514

Answers: 2

Show answers

Another question on Engineering

Engineering, 04.07.2019 18:10

For the closed feedwater heater below, feedwater enters state 3 at a pressure of 2000 psia and temperature of 420 °f at a rate of ix10 ibhr. the feedwat extracted steam enters state 1 at a pressure of 1000 psia and enthalpy of 1500 btu/lbm. the extracted er leaves at an enthalpy of 528.7 btu/lbm steam leaves as a saturated liquid. (16) a) determine the mass flow rate of the extraction steam used to heat the feedwater (10) b) determine the terminal temperature difference of the closed feedwater heater

Answers: 3

Answer

Engineering, 04.07.2019 19:10

What are the major differences between injection molding and extrusion?

Answers: 2

Answer

Engineering, 04.07.2019 19:20

At steady state, air at 200 kpa, 325 k, and mass flow rate of 0.5 kg/s enters an insulated duct having differing inlet and exit cross-sectional areas. the inlet cross-sectional area is 6 cm2. at the duct exit, the pressure of the air is 100 kpa and the velocity is 250 m/s. neglecting potential energy effects and modeling air as an 1.008 kj/kg k, determine ideal gas with constant cp = (a) the velocity of the air at the inlet, in m/s. (b) the temperature of the air at the exit, in k. (c) the exit cross-sectional area, in cm2

Answers: 2

Answer

Engineering, 04.07.2019 19:20

A5 kg block of fe is dropped into a very large vat of water. the fe and water initial temperatures are 95 and 25 c, respectively. the fe final temperature is 25 c and the water can be treated as a thermal reservoir,. treated as a thermal reservoir take the water to be the system and determine the entropy generation. report vour answer in kj/k.

Answers: 1

Answer

You know the right answer?

A. Determination of initial concentrations Volume of 0.25 M NaOH added (mL) 32.77
B. Determi...

Questions

SAT, 02.10.2021 14:00

Which expression is equal to the polynomial below? 2x4 5x3 – 8x – 20 x3(2x 5) 4(2x – 5) x3(2x 5) – 4(2x 5) x3(2x – 5) – 4(2x – 5) x3(2x 5) 4(2x 5)...