![subject](/tpl/images/cats/User.png)
Engineering, 12.11.2020 19:50 jjjxxcsenone1034
Direction shown by the arrow as illustrated in the diagram below, what is going on?
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Ahot wire operates at a temperature of 200°c while the air temperature is 20°c. the hot wire element is a tungsten wire of 5 um diameter and 2 mm in length. plot using excel current, heat transfer and heat generated by the wire for air velocity varying from 1-10 m/s in steps of lm/s? matlab the sensor voltage output, resistance, or assume nu 0.989 re033pr13 take air properties at tr (200°c20°c)/2 = 110°c properties of tungsten: c 0.13 kj/kg.k 3 p 19250 kg/m k (thermal conductivity) = 174 w/m.k
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10
Arigid tank contains 10 kg of air at 137 kpa (abs) and 21°c. more air is added to the tank until the pressure and temperature rise to 242 kpa (abs) and 32°c, respectively. determine the amount of air added to the tank. [r-0.287 kj/kg k]
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 06.07.2019 02:30
Around steel bar, made from material with a yield stress of 750mpa, is loaded so that it has stresses co locations of maximum normal stress and maximum shear stress. use maximum shear stress and maximum distortion energy theories to calculate the safety factors for initial yielding failures.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 06.07.2019 05:20
A8-in.-diameter steel shaft is to have a press fit with a 16-in-diameter cast iron hub. both the hub and the shaft are 10 in long. using maximum normal stress theorem and appropriate safety factor, it was identified that the maximum allowable circumferential (a.k.a. hoop or tangential) stress in the hub is to be 7.5 ksi. the moduli of elasticity are 30 x 106 psi for steel and 15 x 106 psi for cast iron. the poisson's ratio for both steel and cast ron is 0.3 and coefficient friction for the two materials is 0.12. determine a. the interference or the original mismatch, 8 b. the maximum axial force required to press the hub on the shaft
Answers: 1
You know the right answer?
Direction shown by the arrow as illustrated in the diagram below, what is going on?...
Questions
![question](/tpl/images/cats/mat.png)
Mathematics, 04.10.2019 18:00
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 04.10.2019 18:00
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 04.10.2019 18:00
![question](/tpl/images/cats/fizika.png)
Physics, 04.10.2019 18:00
![question](/tpl/images/cats/mat.png)
Mathematics, 04.10.2019 18:00
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 04.10.2019 18:00
![question](/tpl/images/cats/mat.png)
Mathematics, 04.10.2019 18:00
![question](/tpl/images/cats/en.png)
English, 04.10.2019 18:00
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 04.10.2019 18:00
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/himiya.png)
Chemistry, 04.10.2019 18:00
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/himiya.png)
Chemistry, 04.10.2019 18:00
![question](/tpl/images/cats/himiya.png)
Chemistry, 04.10.2019 18:00
![question](/tpl/images/cats/mat.png)
Mathematics, 04.10.2019 18:00
![question](/tpl/images/cats/mat.png)
Mathematics, 04.10.2019 18:00
![question](/tpl/images/cats/biologiya.png)
Biology, 04.10.2019 18:00