Which of the following is a component of BIM?
A) building simulation
B) 2D softwear
C...
![subject](/tpl/images/cats/User.png)
Engineering, 28.08.2020 18:01 zariah10191101
Which of the following is a component of BIM?
A) building simulation
B) 2D softwear
C) manual labor
D) management training
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 03.07.2019 14:10
If the thermal strain developed in polyimide film during deposition is given as 0.0044. assume room temperature is kept at 17.3 c, and thermal coefficient of expansion for the film and the substrate are 54 x 10^-6c^-1 and 3.3 x 10^-6c^-1respectively. calculate the deposition temperature.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Hydraulic fluid with a sg. of 0.78 is flowing through a 1.5 in. i.d. pipe at 58 gal/min. the fluid has an absolute viscosity of 11.8 x 105 lbf-sec/ft2. is the flow laminar, turbulent or within the critical range? give both a numerical reynolds number and a term answer.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20
An open feedwater heater operates at steady state with liquid entering at inlet 1 with t? = 40°c and pl = 1 .2 mpa. water vapor att2-200°c and p2 = 1.2 mpa enters at inlet 2. saturated liquid water exits with a pressure of pa 1.2 mpa. neglect heat transfer with the surroundings and all kinetic and potential energy effects, determine the mass flow rate of steam at inlet 2 if the mass flow rate of liquid water at inlet 1 is given as 2 kg/s.
Answers: 3
You know the right answer?
Questions
![question](/tpl/images/cats/biologiya.png)
Biology, 01.10.2021 02:30
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
History, 01.10.2021 02:30
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mkx.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/himiya.png)
Chemistry, 01.10.2021 02:30
![question](/tpl/images/cats/en.png)
English, 01.10.2021 02:30
![question](/tpl/images/cats/en.png)
English, 01.10.2021 02:30
![question](/tpl/images/cats/istoriya.png)
History, 01.10.2021 02:30
![question](/tpl/images/cats/istoriya.png)
History, 01.10.2021 02:30
![question](/tpl/images/cats/mat.png)
Mathematics, 01.10.2021 02:30
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 01.10.2021 02:30
![question](/tpl/images/cats/himiya.png)
Chemistry, 01.10.2021 02:40
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/himiya.png)