Engineering, 12.08.2020 08:01 zitterkoph

1. In a mechanical design, it is recommended to use standard size/dimension to overcome uncertainties in stress or material strength. A. True
B. False
2. Steels' surface fatigue strength can be correlated to their Brinell hardnesses.
A. True
B. False
3. If a material point has three principal stresses 01 = 02 = 03 = 300kpsi, then the maximum shear stress is Tmax = 150kpsi.
A. True
B. False
4. The endurance limit of a material is independent on the size of a part.
A. True
B. False
5. The tensile stress in a bolt is usually calculated through tensile force divided by area of unthreaded rod's cross-section area.
A. True
B. False
6. Edge shear-out or tear-out is one failure mode in bolted or riveted joints.
A. True
B. False
7. Pretension of bolts can be controlled by a torque wrench.
A. True
B. False
8. The material ultimate tensile strength of a spring coil is dependent on its coil diameter.
A. True
B. False
9. Adhesive joints are much stronger in tensile loading than shear loading.
A. True
B. False
10. The dominated loading condition in a helical spring is torsion along coils.
A. True
B. False
11. The principal advantage of conical springs is that the its spring rate is non-linear.
A. True
B. False
12. The dimensions of a bearing is coded by two-digit series numbers according to ABMA, one digit for width and the other one for diameter.
A. True
B. False
13. Three key things to determine selection of bearing are load, life and reliability.
A. True
B. False
14. Straight roller bearings can carry large radial loads and small amount of axial load.
A. True
B. False
15. In the AGMA method of gear analysis, gear strength values are the true material strengths.
A. True
B. False
16. A planetary gear train allows for two degrees of freedom.
A. True
B. False

Answers: 1

Show answers

Another question on Engineering

Engineering, 03.07.2019 14:10

Amass of m 1.5 kg of steam is contained in a closed rigid container. initially the pressure and temperature of the steam are: p 1.5 mpa and t 240°c (superheated state), respectively. then the temperature drops to t2= 100°c as the result of heat transfer to the surroundings. determine: a) quality of the steam at the end of the process, b) heat transfer with the surroundings. for: p1.5 mpa and t 240°c: enthalpy of superheated vapour is 2900 kj/kg, specific volume of superheated vapour is 0. 1483 m/kg, while for t 100°c: enthalpy of saturated liquid water is 419kj/kg, specific volume of saturated liquid water is 0.001043m/kg, enthalpy of saturated vapour is 2676 kj/kg, specific volume of saturated vapour is 1.672 m/kg and pressure is 0.1 mpa.

Answers: 3

Answer

Engineering, 04.07.2019 18:10

The mass flow rate of the fluid remains constant in all steady flow process. a)- true b)- false

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Courses that are developed by subject matter experts, internal or extemal to the college or university. these programs are marketed by the school (clo2) marks a)-vocational schools b)-vendor training c)-colleges & universities d)-continuing education programs

Answers: 2

Answer

Engineering, 04.07.2019 19:10

Asteam is contained in a rigid tank with a volume of 1 m3. initially, the pressure and temperature are 7 bar and 500 oc, respectively. the temperature drops due to cooling process. determine: (1) the temperature at which condensation begins in °c, (2) the fraction of the total mass that has condensed when the pressure decreased to 0.5 bar. (3) the volume in m3 occupied by saturated liquid at the final state?

Answers: 3

Answer

You know the right answer?

1. In a mechanical design, it is recommended to use standard size/dimension to overcome uncertaintie...

Questions