Engineering, 21.05.2020 03:09 coolsoftball2002

A 50-cm x 50-cm circuit board that contains 121 square chips on one side is to be cooled by combined natural convection and radiation by mounting it on a vertical surface in a room at 25 °C. Each chip dissipates 0.18 W of power, and the emissivity of the chip surfaces is 0.7. Assuming the heat transfer from the back side of the circuit board to be negligible, and the temperature of the surrounding surfaces to be the same as the air temperature of the room, determine the surface temperature of the chips. Evaluate air properties at a film temperature of 30 °C and 1 atm pressure. Is this a good assumption?

Answers: 2

Show answers

Answers

Answer from: heyrosaphoto2610

Ts = 311.86 K = 38.86°C

Explanation:

The convection heat transfer coefficient for vertical orientation of the board is given by the formula:

$h = 1.42(\frac{T_{s} - T_{f} }{L})^{0.25}$

where,

h = heat transfer coefficient

$T_{s}$ = surface temperature

$T_{f}$ = Temperature of fluid (air) = 30°C + 273 = 303 K

L = Characteristic Length = 50 cm = 0.5 m

Since the heat transfer through convection is given as:

$Q_{conv} = hA_{s}(T_{s} - T_{f})$

using value of h, we get:

$Q_{conv} = 1.42(\frac{T_{s} - T_{f} }{L})^{0.25} A_{s} (T_{s} - T_{f} )$

$Q_{conv} = 1.42 A_{s} \frac{(T_{s} - T_{f} )^{1.25} }{L^{0.25} }$

where,

$A_{s}$ = Surface Area = (0.5 m)(0.5 m) = 0.25 m²

Now, the radiation heat transfer is given by:

$Q_{rad} =$ εσ $A_{s} [(T_{s})^{4} - (T_{surr})^{4}]$

where,

ε = emissivity of surface = 0.7

σ = Stefan Boltzman Constant = 5.67 x 10⁻⁸ W/m².k⁴

$T_{surr}$ = Temperature of surroundings = 25°C +273 = 298 k

Now, the total heat transfer rate will be:

$Q_{total} = Q_{conv} + Q_{rad}$

using values:

$Q_{total} =$ $1.42 A_{s} \frac{(T_{s} - T_{f} )^{1.25} }{L^{0.25} } +$ εσ $A_{s} [(T_{s})^{4} - (T_{surr})^{4}]$

we know that the total heat transfer from the board can be found out by:

$Q_{total} = (0.18 W) (121) = 21.78 W$

using values in the equation:

21.78 = (1.42)(0.25) $(T_{s} - 303)^{1.25}/0.5^{0.25}$ + (0.7)(5.67 x 10⁻⁸)(0.25) $[(T_{s})^{4} - 298^{4}]$

21.78 = (0.4222) $(T_{s} - 303)^{1.25}$ + 9.922 x 10⁻⁹ $(T_{s} )^{4}$ - 78.25

100.03 = (0.4222) $(T_{s} - 303)^{1.25}$ + 9.922 x 10⁻⁹ $(T_{s} )^{4}$

Solving this equation numerically by Newton - Raphson Method (Here, any numerical method or an equation solver can be used), we get the value of Ts to be:

Ts = 311.86 K = 38.86°C

The film temperature is the average of surface temperature and surrounding temperature. Therefore,

Film Temperature = (25°C + 38.86°C)/2 = 31.93°C

Since, this is very close to 30°C.

Hence, the assumption is good.

Answer from: Quest

Oh yes igger daddy filled my loose ahοle with your sweet sweet mсum said ronald mcdonald as he spread his sesame covered mcahοle for thanos. thanos slid his throbbing purple ᑕock in to ronald's a. o screamed ronald as he poor hole was torn to bloody shreds. gunga gingagunga gingagunga gingagunga ginga a space ranger appeared making autistuc noises odio a los negros! said buzz lightyear as he aped them both.

Answer from: Quest

answer:

i dont know but you should start brainstorming ideas like how would you post them

explanation:

Another question on Engineering

Engineering, 03.07.2019 23:20

Two technicians are discussing the intake air temperature (iat) sensor. technician a says that the computer uses the iat sensor as a backup to the engine coolant temperature (ect) sensor. technician b says that the powertrain control module (pcm) will subtract the calculated amount of fuel if the air measures hot. who is correct

Answers: 3

Answer

Engineering, 05.07.2019 10:10

What is the correct way to measure the overall length of a boat? measure from the tip of the bow to the highest point on the gunwale. measure from the tip of the bow in a straight line to the stern of the boat. measure from the tip of the bow in a straight line to the back seat. measure from port to starboard at the boat's widest point.

Answers: 1

Answer

Engineering, 06.07.2019 03:10

Different between boring and turning?

Answers: 1

Answer

Engineering, 06.07.2019 04:20

Two microscope slides are placed horizontally, one on top of the other, with a drop of a dishwashing liquid between them. the gap between the slides is 1 mm. a machine pulls the top slide to the right with a velocity of 0.15 millimeters per second while the bottom slide is held stationary. a stress gage indicates that a shearing stress of 0.5 pa is required to pull the top slide with this velocity. if the dishwashing liquid adheres to both slides during this process, what is the viscosity of the liquid? specify whether your answer is dynamic or kinematic viscosity, and use appropriate units.

Answers: 1

Answer

You know the right answer?

A 50-cm x 50-cm circuit board that contains 121 square chips on one side is to be cooled by combined...

Questions