Q.7) The beam shown in figure is supported
by a hinge at point o (which is parallel to x-
...
Engineering, 19.05.2020 16:19 727
Q.7) The beam shown in figure is supported
by a hinge at point o (which is parallel to x-
axis) and a cable. Determine the support
reactions at O and the tension supported by
the cable. [6 marks]
0.8 m
F=(51-12) KN
(ATA = 75 kN, My = 5 kN. m. Mo, = -22 kN. m. O, = 50 kN, 0,= -15 kN,
0, = 54 kN
(B) TAD
= 32.1 kN. M. = 0 kv. m. Mor = 41.4 kN. m, 0, = 15 kN. o, = 23 kN.
0 = -50 kn
(C)TAD = 54 kN, My = -14.4 kN. m. Mo, = 0 kNm, 0, = 23.1 kN. O, = 19 kN.
0,= –22 km
(DTAD = 57 kN. M.y = 4.5 kN. m. Mo, = -44.1 kN. m. 0 = -9k. oy
= 90 KN 0,= 32.1 KN
(E)Other answer Tan = ? N. My =? kN. m.M=? KM,
0,=? kN
0,=? KNO, =? KN.
please help me with this question
Answers: 1
Engineering, 03.07.2019 14:10
Explain the difference laminar and turbulent flow. explain it with the shear stress and the velocity profiles.
Answers: 1
Engineering, 04.07.2019 18:10
Ariver flows from north to south at 8 km/h. a boat is to cross this river from west to east at a speed of 20 km/h (speed of the boat with respect to the earth/ground). at what angle (in degrees) must the boat be pointed upstream such that it will proceed directly across the river (hint: find the speed of the boat with respect to water/river)? a 288 b. 21.8 c. 326 d. 30.2
Answers: 3
Engineering, 04.07.2019 18:10
For the closed feedwater heater below, feedwater enters state 3 at a pressure of 2000 psia and temperature of 420 °f at a rate of ix10 ibhr. the feedwat extracted steam enters state 1 at a pressure of 1000 psia and enthalpy of 1500 btu/lbm. the extracted er leaves at an enthalpy of 528.7 btu/lbm steam leaves as a saturated liquid. (16) a) determine the mass flow rate of the extraction steam used to heat the feedwater (10) b) determine the terminal temperature difference of the closed feedwater heater
Answers: 3
Engineering, 04.07.2019 18:10
Ajournal bearing has a journal diameter of 3.250 in with a unilateral tolerance of 20.003 in. the bushing bore has a diameter of 3.256 in and a unilateral tolerance of 0.004 in. the bushing is 2.8 in long and supports a 700-lbf load. the journal speed is 900 rev/min. find the minimum oil film thickness and the maximum film pressure for both sae 20 and sae 20w-30 lubricants, for the tightest assembly if the operating film temperature is 160°f. a computer code is appropriate for solving this problem.
Answers: 3
Biology, 05.06.2020 14:57
Business, 05.06.2020 14:57
Mathematics, 05.06.2020 14:57
Mathematics, 05.06.2020 14:57
Mathematics, 05.06.2020 14:57
Mathematics, 05.06.2020 14:57
Computers and Technology, 05.06.2020 14:57
Mathematics, 05.06.2020 14:57
Mathematics, 05.06.2020 14:57
Physics, 05.06.2020 14:57
Mathematics, 05.06.2020 14:57