Engineering, 05.05.2020 08:38 heroxtree

A natural gas-fired Brayton cycle with 푚¤ air, Br = 1.15 kg s−1 . (a) Ambient air at 1.00 bar and 300 K is taken in. (b) A compressor with an inlet-to-outlet pressure ratio of 1:15. (c) Regeneration between the compressor and the combustor, increasing the temperature to 850 K (d) Combustion at constant pressure to 1800 K. (e) A two-stage turbine system with reheat between the stages. Reheat occurs at 6.00 bar and raises the temperature to 1700 K. (f) Discharge to a heat exchanger at 1.40 bar, where waste heat is used to warm steam for the Rankine Cycle. The outlet temperature from this heat exchanger is 900 K. (g) From that heat exchanger, discharge to the regeneration heat exchanger in part 1c. 2. A water-steam Rankine Cycle with 푚¤ water, Ra = 1.60 kg s−1 . (a) A two-stage turbine system, with reheat between the stages. The first turbine inlet is at 560 °C and 160 bar. Reheat occurs at 40.0 bar up to 560 °C. The second-stage turbine outlet is 2.00 bar. (b) Cooling at constant pressure in a condenser via heat exchange with ambient air to saturated liquid. The air used in condenser cooling must not exceed 400 K when it is released from the power plant. (c) A pump from the low-side pressure to the high-side pressure. (d) Heating in a boiler at constant pressure, using the waste heat from the Brayton Cycle in a first stage and natural gas combust

Answers: 1

Show answers

Another question on Engineering

Engineering, 04.07.2019 18:20

How much power could a wind turbine produce if it had the following specifications? cp = 0.45 -d=1.2kg/m3 d=50m v 5m/s

Answers: 2

Answer

Engineering, 04.07.2019 19:20

Apreheater involves the use of condensing steam at 100°c on the inside of a bank of tubes to heat air that enters at 1 atm and 25°c. the air moves at 5 m/s in cross flow over the tubes. each tube is 1 m long and has an outside diameter of 10 mm. what is the minimum value of nl needed to achieve an outlet temperature of t 75 c? what is the corresponding pressure drop across the tube bank?

Answers: 3

Answer

Engineering, 06.07.2019 03:10

Tom is having a problem with his washing machine. he notices that the machine vibrates violently at a frequency of 1500 rpm due to an unknown rotating unbalance. the machine is mounted on 4 springs each having a stiffness of 10 kn/m. tom wishes to add an undamped vibration absorber attached by a spring under the machine the machine working frequency ranges between 800 rpm to 2000 rpm and its total mass while loaded is assumed to be 80 kg. a) what should be the mass of the absorber added to the machine so that the natural frequency falls outside the working range? b) after a first trial of an absorber using a mass of 35 kg, the amplitude of the oscillation was found to be 10 cm. what is the value of the rotating unbalance? c) using me-3.5 kg.m, find the optimal absorber (by minimizing its mass). what would be the amplitude of the oscillation of the absorber?

Answers: 1

Answer

Engineering, 06.07.2019 03:20

What is the maximum height from which a mass of 30 kg can fall on to a flange on the lower end of a vertical rod of length 1.0 m and diameter 20 mm, the upper end being rigidly fixed, if the stress in the rod is not to exceed 80 mpa? the tensile modulus of the rod is 200 gpa.

Answers: 3

Answer

You know the right answer?

A natural gas-fired Brayton cycle with 푚¤ air, Br = 1.15 kg s−1 . (a) Ambient air at 1.00 bar and 30...

Questions