subject
Engineering, 06.05.2020 00:16 nadarius2017

URGENT Help with a JK/D Flip Flops, any help would be immensely appreciated.

Anything that you can do will be better than nothing, submit even if it's not complete, Thank You.

Design a counter with an external control, x, to count the sequence of multiples of 3 (i. e., 0-3-6 and repeat) when the control is 0, and non-multiples of 3 (i. e., 1-2-4-5-7 and
repeat) when the control is 1. These values will be displayed on a seven-segment display.

When the control value changes, the first clock should drive the output to the first value in the appropriate count- e. g., if the circuit has been counting
non multiples and the control switches to 0, the first clock should drive the output to 0 (or if you have been counting multiples and the control switches to 1, the first clock pulse
should make the output.

1). Use JK or D flip-flops. For input and output circuits, you may use any chips available in the lab but you must justify your choice, both of your design and of the flip flops you use (combinational logic, decoder, or PLD).

You must demonstrate your counter using your 7-segment display and any additional logic gates/devices that you need to control the circuit.

Note that in a circuit using edge-triggered flip-flops, it may be necessary to use a debounced switch as the clock. Find a suitable circuit that can be built with the items
available in our lab (either online or in a text), and include it, and a proper reference for it, with your prelab.

The prelab you turn in in the lab must include the 1)state table and 2)state diagram for your design, 3)Karnaugh maps (or whatever documentation is required to support your
design) and a 4)schematic of your circuit, (with all pins and gates labeled), along with the debounced switch you found, and the reference to it. NOTE: the debounced switch
design must be done before you come to the lab.

ansver
Answers: 1

Another question on Engineering

question
Engineering, 03.07.2019 14:10
Amass of 1.5 kg of air at 120 kpa and 24°c is contained in a gas-tight, frictionless piston-cylinder device. the air is now compressed to a final pressure of 720 kpa. during the process, heat is transferred from the air such that the temperature inside the cylinder remains constant. calculate the boundary work input during this process.
Answers: 2
question
Engineering, 04.07.2019 18:10
Coiled springs ought to be very strong and stiff. si3n4 is a strong, stiff material. would you select this material for a spring? explain.
Answers: 2
question
Engineering, 04.07.2019 18:10
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
question
Engineering, 04.07.2019 18:10
At 12 noon, the count in a bacteria culture was 400; at 4: 00 pm the count was 1200 let p(t) denote the bacteria cou population growth law. find: (a) an expression for the bacteria count at any time t (b) the bacteria count at 10 am. (c) the time required for the bacteria count to reach 1800.
Answers: 1
You know the right answer?
URGENT Help with a JK/D Flip Flops, any help would be immensely appreciated.

Anything th...
Questions
question
Mathematics, 03.10.2019 03:30
question
Mathematics, 03.10.2019 03:30
question
Mathematics, 03.10.2019 03:30