Engineering, 15.04.2020 03:03 torresq6647

A brass alloy is known to have a yield strength of 275 MPa (40,000 psi), a tensile strength of 380 MPa (55,000 psi), and an elastic modulus of 103 GPa (15.0×106 psi). A cylindrical specimen of this alloy 5.5 mm (0.22 in.) in diameter and 267 mm (10.52 in.) long is stressed in tension and found to elongate 7.0 mm (0.28 in.). On the basis of the information given, is it possible to compute the magnitude of the load that is necessary to produce this change in length? If not, explain why.

Answers: 1

Show answers

Answers

Answer from: renaudciera

Computation of the load is not possible because E(test) >E(yield)

Explanation:

We are asked to ascertain whether or not it is possible to compute, for brass, the magnitude of the load necessary to produce an elongation of 7.0 mm (0.28 in.). It is first necessary/ important to compute the strain at yielding from the yield strength and the elastic modulus, and then the strain experienced by the test specimen. Then, if

E(test) is less than E(yield), deformation is elastic and the load may be computed. However is E(test) is greater than E(yield) computation/determination of the load is not possible even though defamation is plastic and we have neither a stress-strain plot or a mathematical relating plastic stress and strain. Therefore, we can compute these two values as:

Calculation of E(test is as follows)

E(test) = change in l/lo= Elongation produced/stressed tension= 7.0mm/267mm

=0.0262

Computation of E(yield) is given below:

E(yield) = σy/E=275Mpa/103 ×10^6Mpa= 0.0027

Therefore, we won't be able to compute the load because for computation to take place, E(test) <E(yield). In this case, E(test) is greater than E(yield).

Answer from: kamraaa

It's not possible to compute the magnitude of the load

Explanation:

Given data:

Yield strength = 275Mpa

Tensile strength = 380Mpa

Elastic modulus = 103Gpa = 103 * 1000MPa

Diameter = 5.5 mm

Length = 267 mm

Elongation = 7.0 mm

Calculating the strain test value using the formula'

ε(test) = ΔL/Lo

Substituting, we have

ε = 7.0/267

= 0.0262

Calculating the yield strain using the formula

ε(yield) = бy/E

Substituting, we have

ε(yield) = 275/ 103 * 1000

= 275/103000

= 0.00267

From the calculation above, the strain test is greater than the yield. Therefore, it's not possible to compute the magnitude of the load.

ε(test) ⊃ ε(yield)

Answer from: Quest

answer:

ok yeah for me again

explanation:

Answer from: Quest

Yes. It’s the best product on the market for leaks.

Another question on Engineering

Engineering, 04.07.2019 18:10

The mass flow rate of the fluid remains constant in all steady flow process. a)- true b)- false

Answers: 1

Answer

Engineering, 04.07.2019 18:10

An air conditioning system consist of a 5 cm diameter pipe, operating at a pressure of 200 kpa. the air initially enters the pipe at 15°c with a velocity of 20 m/s and relative humidity of 80%. if the heat supply throughout the process is 960 w, determine the relative humidity and the temperature at the outlet

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Coiled springs ought to be very strong and stiff. si3n4 is a strong, stiff material. would you select this material for a spring? explain.

Answers: 2

Answer

Engineering, 04.07.2019 18:10

Condition monitoring is a major component of. (clo4) a)- predictive maintenance. b)-preventive maintenance c)-proactive maintenance d)-reactive maintenance.

Answers: 1

Answer

You know the right answer?

A brass alloy is known to have a yield strength of 275 MPa (40,000 psi), a tensile strength of 380 M...

Questions