Engineering, 15.04.2020 00:56 walfrerr

1. Think about what you’ve learned about BJTs, both from lecture and from lab. What aspects of the transfer functions of the CE amplifier and the emitter follower can you sketch on your own (i. e. without having the PSpice simulation or Labview measurement)? What value does PSpice add to your ability to analyze these circuits?

Answers: 1

Show answers

Answers

Answer from: gisellekatherine1

Check all the explanations below. Also check all the attached files for additional information

Explanation:

A Bipolar Junction Transistor is a semiconductor device consisting of two P-N Junctions connecting three terminals called the Base, Emitter and Collector terminals. The current and the gain of theses transistors is determined by the arrangement of these terminals. The BJT uses both electrons and holes as the charge carriers. The BJT can be of two types, the PNP and the NPN transistors.

The common emitter amplifier is a three basic single-stage bipolar junction transistor and is used as a voltage amplifier. In this configuration, the emitter terminal is common to both the collector and the base, the input to the amplifier is taken from the base while the output is taken from the collector.

The common emitter amplifier circuit is attached as a file to this solution.

The current gain of a common emitter amplifier is $\beta = \frac{\triangle I_{c} }{\triangle I_{B} }$

where $I_{c} and I_{B}$ are the collector and emitter currents respectively

The voltage gain of the amplifier is given by $A_{v} = \beta \frac{R_{c} }{R_{B} }$

$R_{c} and R_{B}$ are the collector and base resistance respectively

In an emitter follower configuration, emitter follows the voltage on the base. It is also called the common collector configuration. The collector is common to the emitter and base terminals.

The common collector configuration is shown in the second file attached

The output voltage on a common-collector amplifier will be in phase with the input voltage, making the common-collector a non-inverting amplifier circuit.

The current gain = $\beta + 1$

Voltage gain = 1 ( Approximately)

Pspice helps in the simulation and analysis of electronic and electrical circuits without going through the rigors of using a pen and paper. It also allows us to test with real data and make proper choice of values.

1. Think about what you’ve learned about BJTs, both from lecture and from lab. What aspects of the t

Answer from: Quest

the correct answer is c.stops after infancy and childhood.

myelin is the substance of the central nervous system (cns) that insulates nerve cell axons to increase the speed at which nerve impulse travels. myelination is a process of myelin formation. this process occurs postnatally, begins in the embryo during the midst of early development and finishes after birth.

Answer from: Quest

answer: make you irritable

Another question on Engineering

Engineering, 04.07.2019 16:10

An electrical motor raises a 50kg load at a construct velencity .calculate the power of the motor, if it takes 40sec to raise the load through a height of 24m(take g =9.8n/g)

Answers: 2

Answer

Engineering, 04.07.2019 18:10

Machinery that is a key part of the process and without which the plant or process cannot function is classifed as: (clo4) a)-critical machinery b)-essential machinery c)-general purpose machinery d)-none of the specified options.

Answers: 1

Answer

Engineering, 04.07.2019 19:10

The air in an automobile tire with a volume of 0.015 m3 is at 32°c and 140 kpa gage. determine the amount of air that must be added to raise the pressure to the recommended value of 206 kpa gage. assume the atmospheric pressure to be 128 kpa and the temperature and the volume to remain constant.[r-0.287 kj/kgk]

Answers: 3

Answer

Engineering, 04.07.2019 19:20

List 3 options on how to reduce knocking problens during engine process,

Answers: 2

Answer

You know the right answer?

1. Think about what you’ve learned about BJTs, both from lecture and from lab. What aspects of the t...

Questions