Engineering, 23.03.2020 22:46 cair6415

HW6P2 (20 points) The recorded daily temperature (°F) in New York City and in Denver, Colorado during the month of January 2014 is given by the data file NYCDen Jan 14.dat (data from the U. S. National Oceanic and Atmospheric Administration). The first column is the day of the month 2ad column is NYC temperatures and 3 column is Denver temperature. Write a MATLAB program in a script file HW6P2.m that does the following: a) (1 pt) Imports the data file NYCDen Jan14.dat b) (2 pts) Assigns the columns of NYCDen Jan 14 to variables DAY, T. NYC and T_DEN, respectively c) (3 pts) Determines the average temperature for the month of January 2014 in each city (rounded to the nearest degree). You can use the mean() built-in MATLAB function to calculate the average. Your display must be in the format "The average temperature in sss for Jan. 2014 is XX *P." Where sss refers to the name of the city and xx refers to the temperature value. This text must be displayed for each city d) (3 pts) Determines and displays the number of days where the temperat was above the average of that city. Your display must be in the format "The temperature in Sss was above the average for xx days. This text must be displayed for each city refers to the number of days while sss refers to the city 0) (3 pts) Determines and displays the number of days where the temperature in each city was above the average of NYC but below the average of DEN. Your display must be in the format "The temperature in SSS was above NYC average and below DEN average for Xx days. This text must be displayed for each city. refers to the number of days while sss refers to the city. (3 pts) Determines and displays the number of days where the temperature in each city was above either the average of NYC or the average of DEN. Your display must be in the format "The temperature in SSS was above either NYC average or DEN average for xx days. This text must be displayed for each city, OK refers to the number of days while sss refers to the city. 8) (5 pts) Determines and displays the days that the temperature in Denver was lower than the temperature in New York city and the temperature difference for these days. Your display must be repeated for all days in the format: On Jan. xx 2014, DEN temp. was lower than NYC temp. by Xx . XX refers to the day or the value of the temperature difference. Use fprintf() with 1 format character to display Xox data with a field width of 2. Do Not define a field width for SSS strings. Leave a blank line between every data set (cd. e. f and g) displayed in the command window.

Answers: 1

Show answers

Another question on Engineering

Engineering, 04.07.2019 18:10

Hydraulic fluid with a sg. of 0.78 is flowing through a 1.5 in. i.d. pipe at 58 gal/min. the fluid has an absolute viscosity of 11.8 x 105 lbf-sec/ft2. is the flow laminar, turbulent or within the critical range? give both a numerical reynolds number and a term answer.

Answers: 3

Answer

Engineering, 04.07.2019 19:10

With increases in magnification, which of the following occur? a. the field of view decreases. b. the ambient illumination decreases. c. the larger parts can be measured. d. the eyepiece must be raised.

Answers: 1

Answer

Engineering, 04.07.2019 19:10

The air in an automobile tire with a volume of 0.015 m3 is at 32°c and 140 kpa gage. determine the amount of air that must be added to raise the pressure to the recommended value of 206 kpa gage. assume the atmospheric pressure to be 128 kpa and the temperature and the volume to remain constant.[r-0.287 kj/kgk]

Answers: 3

Answer

Engineering, 04.07.2019 19:20

Liquid flows at steady state at a rate of 2 lb/'s through a pump, which operates to raise the elevation of the liquid 100 ft from control volume inlet to exit. the liquid specific enthalpy at the inlet is 40.09 btu/lb and at the exit is 40.94 btub. the pump requires 3 btu/s of power to operate. if kinetic energy effects are negligible and gravitational acceleration is 32.174 tt/s, the heat transfer rate associated with this steady state process is most closely 1)-2,02 btu/s from the liquid to the surroundings 2)-3.98 btu/s from the surroundings to the liquid. 3)-4.96 btu/s from the surroundings to the liquid. 4)-1.04 btu/s from the liquid to the surroundings.

Answers: 2

Answer

You know the right answer?

HW6P2 (20 points) The recorded daily temperature (°F) in New York City and in Denver, Colorado durin...

Questions