Question 10
Which of the listed components provides the most resistance to
w...
![subject](/tpl/images/cats/User.png)
Engineering, 19.03.2020 08:31 elijahjacksonrp6z2o7
Question 10
Which of the listed components provides the most resistance to
wheel rotation on a hybrid during normal braking?
OA) Front brakes
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-cm-outer-diameter and 0.4-m-long tubes inside which the refrigerant is evaporating at -20°c. air approaches the tube bank in the normal direction at 0°c and 1 atm with a mean velocity of 4 m/s. the tubes are arranged in-line with longitudinal and transverse pitches of sl- st 1.5 cm. there are 30 rows in the flow direction with 15 tubes in each row. determine (a) the refrigeration capacity of this system and (b) pressure drop across the tube bank. evaluate the air properties at an assumed mean temperature of -5°c and 1 atm. is this a good assumption?
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Water at the rate of 1 kg/s is forced through a tube with a 2.5 cm inner diameter. the inlet water temperature is 15°c, and the outlet water temperature is 50°c. the tube wall temperature is 14°c higher than the local water temperature all along the length of the tube. what is the length of the tube?
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:20
Air enters a horizontal, constant-diameter heating duct operating at steady state at 290 k, 1 bar, with a volumetric flow rate of 0.25 m°/s, and exits at 325 k, 0.95 bar. the flow area is 0.04 m2. assuming the ideal gas model with k = 1.4 for the air, determine (a) the velocity at the inlet and exit, each in m/s, and (c) the rate of heat transfer, in kw flow rate, in kg/s, (b) the mass kg 0.3
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 06.07.2019 02:30
An electric motor is used to drive a power press which makes steel turning moment diagrams 323 pressings from a metal sheet. the motor runs at a mean speed of 50 rev/s. the torque required is 10.0nm for 0.2s, followed by 1.0nm for0.3 s with this sequence then being repeated. what is the minimum power required of the motor and the moment of incrtia required for the t1ywhcel if the speed fluctuations are to be restricted to 1.5%?
Answers: 3
You know the right answer?
Questions
![question](/tpl/images/cats/mkx.png)
Arts, 23.04.2021 22:50
![question](/tpl/images/cats/mat.png)
Mathematics, 23.04.2021 22:50
![question](/tpl/images/cats/mat.png)
Mathematics, 23.04.2021 22:50
![question](/tpl/images/cats/mat.png)
Mathematics, 23.04.2021 22:50
![question](/tpl/images/cats/mat.png)
Mathematics, 23.04.2021 22:50
![question](/tpl/images/cats/mat.png)
Mathematics, 23.04.2021 22:50
![question](/tpl/images/cats/mat.png)
Mathematics, 23.04.2021 22:50
![question](/tpl/images/cats/mat.png)
Mathematics, 23.04.2021 22:50
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/en.png)
English, 23.04.2021 22:50
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 23.04.2021 22:50
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 23.04.2021 22:50
![question](/tpl/images/cats/mat.png)
Mathematics, 23.04.2021 22:50
![question](/tpl/images/cats/himiya.png)
Chemistry, 23.04.2021 22:50