![subject](/tpl/images/cats/User.png)
Engineering, 11.03.2020 23:57 kaylallangari2145
The yield strength for an alloy that has an average grain diameter of 5.9 × 10-2 mm is 128 MPa. At a grain diameter of 6.6 × 10-3 mm, the yield strength increases to 268 MPa. At what grain diameter, in mm, will the yield strength be 236 MPa?
![ansver](/tpl/images/cats/User.png)
Answers: 2
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 16:10
An electrical motor raises a 50kg load at a construct velencity .calculate the power of the motor, if it takes 40sec to raise the load through a height of 24m(take g =9.8n/g)
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Afour cylinder four-stroke in-line engine has a stroke of 160mm, connecting rod length of 150mm, a reciprocating mass of 3kg and its firing order is 1-3-4-2. the spacing between cylinders is 100mm. i. show that the engine is in balance with regard to the primary inertia forces and primary 3. a and secondary inertia couples. li determine the out of balance secondary inertia force ii. propose ways of balancing this out of balance force and discuss the challenges that will arise
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Adouble-strand no. 60 roller chain is used to transmit power between a 13-tooth driving sprocket rotating at 300 rev/min and a 52-tooth driven sprocket. a) what is the allowable horsepower of this drive? b) estimate the center-to-center distance if the chain length is 82 pitches. c) estimate the torque and bending force on the driving shaft by the chain if the actual horsepower transmitted is 30 percent less than the corrected (allowable) power.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Which of the following ziegler nichols tuning methods the response of the controller to a step input should exhibit an s-shaped curve? a)-open loop mode b)-closed loop mode c)-both modes (open & closed) d)-none of the modes (open & closed)
Answers: 3
You know the right answer?
The yield strength for an alloy that has an average grain diameter of 5.9 × 10-2 mm is 128 MPa. At a...
Questions
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 14.10.2019 22:30
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
English, 14.10.2019 22:30
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/mkx.png)
![question](/tpl/images/cats/en.png)
English, 14.10.2019 22:30
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 14.10.2019 22:30
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 14.10.2019 22:30
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 14.10.2019 22:30
![question](/tpl/images/cats/mat.png)
Mathematics, 14.10.2019 22:30
![question](/tpl/images/cats/mat.png)