Engineering, 19.02.2020 04:26 tqjb2007

A steady tensile load of 5.00kN is applied to a square bar, 12mm on a side and having a length of 1.65m. compute the stress in the bar and the resulting design factor if it is made from: (a) AISI 120 hot-rolled steel (b) AISI 8650 OQT 1000 steel, (c) ductile iron A536-84 (60-40-18) (d) aluminum allot 6061-T6 (e) titanium alloy Ti-6Al-4V annealed (f) rigid PVC plastic and (g) pheonolic plastic

Answers: 1

Show answers

Answers

Answer from: areyonalloyd

The stress in the bar is 34.72 MPa.

The design factor (DF) for each case is:

A) DF=0.17

B) DF=0.09

C) DF=0.125

D) DF=0.12

E) DF=0.039

F) DF=1.26

G) DF=5.5

Explanation:

The design factor is the relation between design stress and failure stress. In the case of ductile materials like metals, the failure stress considered is the yield stress. In the case of plastics or ceramics, the failure stress considered is the breaking stress (ultimate stress). If the design factor is less than 1, the structure or bar will endure the applied stress. By the opposite side, when the DF is higher than 1, the structure will collapse or the bar will break.

we will calculate the design stress in this case:

$\displaystyle \sigma_{dis}=\frac{T_l}{Sup}=\frac{5.00KN}{(12\cdot10^{-3}m)^2}=34.72MPa$

The design factor for metals is:

$DF=\displaystyle \frac{\sigma_{dis}}{\sigma_{f}}=\frac{\sigma_{dis}}{\sigma_{y}}$

The design factor for plastic and ceramics is:

$DF=\displaystyle \frac{\sigma_{dis}}{\sigma_{f}}=\frac{\sigma_{dis}}{\sigma_{u}}$

We now need to know the yield stress or the ultimate stress for each material. We use the AISI and ASTM charts for steels, materials charts for non-ferrous materials and plastics safety charts for the plastic materials.

For these cases:

A) The yield stress of AISI 120 hot-rolled steel (actually is AISI 1020) is 205 MPa, therefore:

$DF=\displaystyle\frac{34.72MPa}{205MPa}=0.17$

B) The yield stress of AISI 8650 OQT 1000 steel is 385 MPa, therefore:

$DF=\displaystyle\frac{34.72MPa}{385MPa}=0.09$

C) The yield stress of ductile iron A536-84 (60-40-18) is 40Kpsi, this is 275.8 MPa, therefore:

$DF=\displaystyle\frac{34.72MPa}{275.8MPa}=0.125$

D) The yield stress of aluminum allot 6061-T6 is 290 MPa, therefore:

$DF=\displaystyle\frac{34.72MPa}{290MPa}=0.12$

E) The yield stress of titanium alloy Ti-6Al-4V annealed (certified by manufacturers) is 880 MPa, therefore:

$DF=\displaystyle\frac{34.72MPa}{880MPa}=0.039$

F) The ultimate stress of rigid PVC plastic (certified by PVC Pipe Association) is 4Kpsi or 27.58 MPa, therefore:

$DF=\displaystyle\frac{34.72MPa}{27.58 MPa}=1.26$

In this case, the bar will break.

F) You have to consider that phenolic plastics are used as matrix in composite materials and seldom are used alone with no reinforcement. In this question is not explained if this material is reinforced or not, therefore I will use the ultimate stress of most pure phenolic plastics, in this case, 6.31 MPa:

$DF=\displaystyle\frac{34.72MPa}{6.31 MPa}=5.5$

This material will break.

Answer from: Quest

Idon’t do engeneering classes sorry

Answer from: Quest

answer:

what happend?

explanation:

Another question on Engineering

Engineering, 04.07.2019 18:10

Adouble-strand no. 60 roller chain is used to transmit power between a 13-tooth driving sprocket rotating at 300 rev/min and a 52-tooth driven sprocket. a) what is the allowable horsepower of this drive? b) estimate the center-to-center distance if the chain length is 82 pitches. c) estimate the torque and bending force on the driving shaft by the chain if the actual horsepower transmitted is 30 percent less than the corrected (allowable) power.

Answers: 3

Answer

Engineering, 04.07.2019 19:10

What are the major differences between injection molding and extrusion?

Answers: 2

Answer

Engineering, 04.07.2019 19:10

A)-in the process of engineering design, explain the contribution of material selection. b)- explain the procedure of synthesis as is employed in engineering design. c)- is there any relationship between ergonomics and engineering design? explain. d)- safety consideration in engineering design includes human, product and the enviroment . explain how safety will be incorporated into the design?

Answers: 3

Answer

Engineering, 04.07.2019 19:10

Which of the following is the most important advantage of a large field of view? a. allows larger areas to be examined b. relieves eyestrain c. minimizes parallax errors. d. increases precision in proportion to the in- crease in field of view

Answers: 2

Answer

You know the right answer?

A steady tensile load of 5.00kN is applied to a square bar, 12mm on a side and having a length of 1....

Questions