![subject](/tpl/images/cats/User.png)
Engineering, 19.12.2019 21:31 darkcrystal463
Using fig. 17.13, select the minimum-length boom required to hoist a load of 80,000 lb from a truck at ground level and place it on a platform 76 ft above the ground. the minimum allowable vertical distance from the bottom of the load to the boom point of the crane is 42 ft. the maximum horizontal distance from the center of rotation of the crane to the hoist line of the crane when lifting the load is 40 ft.
![ansver](/tpl/images/cats/User.png)
Answers: 3
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Adouble-strand no. 60 roller chain is used to transmit power between a 13-tooth driving sprocket rotating at 300 rev/min and a 52-tooth driven sprocket. a) what is the allowable horsepower of this drive? b) estimate the center-to-center distance if the chain length is 82 pitches. c) estimate the torque and bending force on the driving shaft by the chain if the actual horsepower transmitted is 30 percent less than the corrected (allowable) power.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
An ideal otto cycle with air as the working fluid has a compression ratio of 8. the minimum and maximum temperatures in the cycle are 300 k and 1340 k. use constant specific heats at room temperature to determine (a) the amount of heat transferred to the air during the heat- addition kj/kg, (b) the thermal efficiency, and (c) the thermal efficiency of a carnot cycle ope limits. process, in rating between the same temperature
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10
When subject to a steady load (within elastic range) over a long period of time, what is the major difference in material behavoir between steel and plastic?
Answers: 2
You know the right answer?
Using fig. 17.13, select the minimum-length boom required to hoist a load of 80,000 lb from a truck...
Questions
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 01.11.2019 17:31
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/himiya.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 01.11.2019 17:31
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 01.11.2019 17:31
![question](/tpl/images/cats/User.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/mat.png)
Mathematics, 01.11.2019 17:31
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/istoriya.png)
History, 01.11.2019 17:31