Engineering, 07.10.2019 19:20 datstepparoddoe27

G2) steel rod (1) is fastened to brass rod (2) with a pin at b. the diameter of the pin is 7 /8 in. both rods are fixed at their ends a and c. the cross-sectional area of the steel rod is 1 in2 and the brass rod 1.5 in2 . the coefficient of thermal expansion for the steel is 6.5 x 10-6 /°f and its elastic modulus is 29 x 103 ksi. the coefficient of thermal expansion for the brass is 11.3 x 10-6 /°f and its elastic modulus is 15 x 103 ksi. a) the temperature drops 40°f. write the equilibrium and compatibility equation(s) needed to solve the problem along with supporting sketches. b) calculate the internal force in members (1) and (2) in kips. indicate tension or compression. [ans. to check: f1 = 9.2 k] c) calculate the average normal stress in each member in ksi. indicate tension or compression. d) compute the shear stress in the pin at b in ksi. [ans. to check: τ = 15.3 ksi] e) calculate the movement at b in inches. clearly indicate direction.

Answers: 2

Show answers

Another question on Engineering

Engineering, 03.07.2019 15:10

Two flowing streams of argon gas are adiabatically mixed to form a single flow/stream. one stream is 1.5 kg/s at 400 kpa and 200 c while the second stream is 2kg/s at 500 kpa and 100 ? . it is stated that the exit state of the mixed single flow of argon gas is 150 c and 300 kpa. assuming there is no work output or input during the mixing process, does this process violate either the first or the second law or both? explain and state all your assumptions.

Answers: 1

Answer

Engineering, 03.07.2019 23:20

Two technicians are discussing the intake air temperature (iat) sensor. technician a says that the computer uses the iat sensor as a backup to the engine coolant temperature (ect) sensor. technician b says that the powertrain control module (pcm) will subtract the calculated amount of fuel if the air measures hot. who is correct

Answers: 3

Answer

Engineering, 04.07.2019 18:10

Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.

Answers: 1

Answer

Engineering, 04.07.2019 18:10

Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-cm-outer-diameter and 0.4-m-long tubes inside which the refrigerant is evaporating at -20°c. air approaches the tube bank in the normal direction at 0°c and 1 atm with a mean velocity of 4 m/s. the tubes are arranged in-line with longitudinal and transverse pitches of sl- st 1.5 cm. there are 30 rows in the flow direction with 15 tubes in each row. determine (a) the refrigeration capacity of this system and (b) pressure drop across the tube bank. evaluate the air properties at an assumed mean temperature of -5°c and 1 atm. is this a good assumption?

Answers: 1

Answer

You know the right answer?

G2) steel rod (1) is fastened to brass rod (2) with a pin at b. the diameter of the pin is 7 /8 in....

Questions