The early steam engines were driven by the atmosphericpressure
acting on the piston fitt...
![subject](/tpl/images/cats/User.png)
Engineering, 02.10.2019 00:30 jwhit28
The early steam engines were driven by the atmosphericpressure
acting on the piston fitted into a cylinder filled withsaturated
steam. a vacuum was created in the cylinder by coolingthe cylinder
externally with cold water, and thus condensing thesteam.
consider a piston-cylinder devise with a piston surface areaof
0.1m2 initially with 0.05m3 of saturatedsteam
at the atmospheric pressure of 100kpa. now cold water ispoured
outside the cylinder, and the steam inside starts tocondensing as a
result of heat transfer to the cooling wateroutside. if the piston
is stuck at its initial position, determinethe friction force
acting on the piston, and the amount of heattransfer when the
temperature inside the cylinder drops to30oc.
![ansver](/tpl/images/cats/User.png)
Answers: 1
![](/tpl/images/ask_question.png)
![](/tpl/images/ask_question_mob.png)
Another question on Engineering
![question](/tpl/images/cats/User.png)
Engineering, 03.07.2019 14:10
If the thermal strain developed in polyimide film during deposition is given as 0.0044. assume room temperature is kept at 17.3 c, and thermal coefficient of expansion for the film and the substrate are 54 x 10^-6c^-1 and 3.3 x 10^-6c^-1respectively. calculate the deposition temperature.
Answers: 3
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Refrigerant 134a enters an insulated compressor operating at steady state as saturated vapor at -26°c with a volumetric flow rate of 0.18 m3/s. refrigerant exits at 9 bar, 70°c. changes in kinetic and potential energy from inlet to exit can be ignored. determine the volumetric flow rate at the exit, in m3/s, and the compressor power, in kw.
Answers: 1
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Shafts are machine elements that are used to a) carry axial loads b) direct shear loads c) transmit power d) rotate at constant speed e) none of the above circular and square shafts subjected to the same torque under the same circum behave a) the same way b) almost the same way
Answers: 2
![question](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10
Slip occurs via two partial dislocations because of (a) the shorter path of the partial dislocation lines; (b) the lower energy state through partial dislocations; (c) the charge balance.
Answers: 1
You know the right answer?
Questions
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/en.png)
English, 15.10.2019 02:10
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 15.10.2019 02:10
![question](/tpl/images/cats/en.png)
![question](/tpl/images/cats/biologiya.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/es.png)
![question](/tpl/images/cats/mat.png)
![question](/tpl/images/cats/biologiya.png)
Biology, 15.10.2019 02:10
![question](/tpl/images/cats/obshestvoznanie.png)
![question](/tpl/images/cats/istoriya.png)
History, 15.10.2019 02:10
![question](/tpl/images/cats/ekonomika.png)
![question](/tpl/images/cats/fizika.png)
![question](/tpl/images/cats/geografiya.png)
![question](/tpl/images/cats/istoriya.png)
![question](/tpl/images/cats/mat.png)