Engineering, 07.08.2019 17:10 ale2035

Athin rim with a mean diameter of 1.2 m cross-section of 15 mm x 200 mm is subjected to an internal pressure of 10 mpa and rotates at 800 r/min. calculate 1. the magnitude of the force and the stress in the rim if the density of the materials is 7800 kg/m3. 2. the total change in diameter. young's modulus for the material is 200 gpa.

Answers: 1

Show answers

Answers

Answer from: emory238

The net centrifugal force over the rim is 30000N, the radial stress is 397887 Pa and the total change in diameter is 4.98 mm.

Explanation:

Lets first calculate the force in the rim due to the centrifugal force. For doing this we may assume that the centrifugal force is constant along with thick because of the thin thick.

Fc = m.ω^2/R

Where m is the mass, w the angular speed and R the mean radius. The mass is computing by the rim density and its volume:

m=p.V

m=p*(A*R)

Where A is the cross-sectional area in meters:

m=((0.015m*0.200m)*0.6m)*(7800 kg/m^3)=28.08 kg

The angular speed in rad/s is:

ω = 800r/m . 1m/60s = 133.33 r/s

Thus the centrifugal force is:

Fc = (28.08 kg)*(133.33 rad/s)^2*(0.6m) = 299505N = 30000N

Note that the calculating value is the net contribution to the whole rim but the centrifugal force is distributed along the rim's external area:

fc = Fc / (2π .R .b)

Where b is rim's with equal to 200mm :

fc = 300000 N / (2π*0.6m*0.2m) = 397887 N/m^2

The centrifugal force can be taken as internal pressure:

Pfc = 397887 N/m^2 = 3978787 Pa

As both pressures act expanding the rim it can be summed:

Pt=Pi+Pfc

Pt = 10MPa+397887Pa= 10000000Pa+397887Pa= 10397887Pa

Then for a thinner thick the stress is calculated by:

Pt*d =2σr*t

Take into account that the stress σr is over the radial direction. Then solving for o and by replacing the total pressure:

σr = Pt.d/(2*t)

σr = 10397887 Pa / (2*0.015m*0.2m) = 415915480Pa = 415MPa

We know that the radial specific deformation ε is:

σr = E / εr

εr = σr / E

For a young modulus of 200GPa:

εr = 415MPa / 200GPa

εr = 415MPa / 200000MPa=0.002075

By definition the specific deformation is written in terms of the total change in the radius:

εr = Δr / R

Δr = R / εr =0.002075 * 1.2 m = 0.00249m

As we need the change in diameter:

Δd = 2Δr =0.00498m= 4.98mm [/tex]

Answer from: Quest

answer:

what

explanation:

Answer from: Quest

answer:

ur mom

explanation:

Another question on Engineering

Engineering, 04.07.2019 18:10

Aplate clutch has a single pair of mating friction surfaces 250-mm od by 175-mm id. the mean value of the coefficient of friction is 0.30, and the actuating force is 4 kn. a) find the maximum pressure and the torque capacity using the uniform-wear model. b) find the maximum pressure and the torque capacity using the uniform-pressure model.

Answers: 3

Answer

Engineering, 04.07.2019 18:10

For the closed feedwater heater below, feedwater enters state 3 at a pressure of 2000 psia and temperature of 420 °f at a rate of ix10 ibhr. the feedwat extracted steam enters state 1 at a pressure of 1000 psia and enthalpy of 1500 btu/lbm. the extracted er leaves at an enthalpy of 528.7 btu/lbm steam leaves as a saturated liquid. (16) a) determine the mass flow rate of the extraction steam used to heat the feedwater (10) b) determine the terminal temperature difference of the closed feedwater heater

Answers: 3

Answer

Engineering, 04.07.2019 18:10

The thermal expansion or contraction of a given metal is a function of the f a)-density b)-initial temperature c)- temperature difference d)- linear coefficient of thermal expansion e)- final temperature f)- original length

Answers: 2

Answer

Engineering, 04.07.2019 19:10

10 kg of co2 is initially contained at 400 kpa and 300 k. the gas constant for carbon dioxide is 189 j/lkg k) and has a specific heat ratio, k, of 1.289. isentropic expansion then occurs until the pressure is 200 kpa. a) determine the initial volume of co2 in m. b) determine the final temperature in k. c) determine the work done by the system during the expansion kl.

Answers: 2

Answer

You know the right answer?

Athin rim with a mean diameter of 1.2 m cross-section of 15 mm x 200 mm is subjected to an internal...

Questions