subject

Create a newsletter using word processing software. Directions In this assignment, you'll use a word processor to create a newsletter based on the following scenario: Suppose that you are a secretary at a high school. You need to provide the students with information about upcoming events and a reminder about the cell phone policy. The cell phone policy states that all cell phones need to be turned off while on the school campus until dismissal time. After the dismissal bell, phones may be turned on and used. The events that should be in the newsletter include a dance, chess tournament, community garden, basketball game, and fundraiser. Your newsletter should fill-in the details for these events and meet these requirements: • List school contact information. • Fill one page. • Include the following: o two or three columns; o a title; o at least three graphics, but not more than six. When you've finished creating your newsletter, remember to spell check and proofread. Then save your newsletter and upload it.​

ansver
Answers: 1

Another question on Computers and Technology

question
Computers and Technology, 21.06.2019 21:30
What is linux? an open source operating system a version of ms dos the first version of unix the newest technology available
Answers: 1
question
Computers and Technology, 22.06.2019 03:00
Check my work the microprocessor is a(n) circuit, which is designed to process data based on a set of instructions. most desktop and laptop devices contain a microprocessor based on the standard. most tablets and smartphones contain processors based on technology. a microprocessor's circuitry is designed to perform a limited number of tasks contained in its set. during processing, an instruction is loaded into the processor's unit. data is loaded into registers in the processor's where arithmetic and logic operations are performed. microprocessor performance can be measured by its speed. other factors affecting overall processing performance include word size, cache size, and instruction set complexity. most digital devices contain only one microprocessor chip, but today's multi- processors contain circuitry that supports parallel processing. computers contain various kinds of memory. random memory is a special holding area for data, program instructions, and the system. it stores data on a temporary basis until the processor makes a data request. ram is different from disk storage because it is , which means that it can hold data only when the computer power is turned on. computers also contain read- memory, which is a type of non-volatile memory that provides a set of "hard-wired" instructions, called the loader, that a computer uses to boot up.
Answers: 3
question
Computers and Technology, 22.06.2019 20:30
In this lab, you complete a prewritten c program that calculates an employee’s productivity bonus and prints the employee’s name and bonus. bonuses are calculated based on an employee’s productivity score as shown below. a productivity score is calculated by first dividing an employee’s transactions dollar value by the number of transactions and then dividing the result by the number of shifts worked.
Answers: 3
question
Computers and Technology, 22.06.2019 23:50
You need to design a circuit that implements the functions in the following table: s0 s1 function0 0 a + 10 1 a – b1 0 a + b1 1 a – 1s0 and s1 are 1-bit control inputs to select the function of the circuit. inputs a and b are 4-bitnumbers in 2s complement form. the output is also a 4-bit number in 2s complement form.you are allowed to use only one ttl 7483 4-bit adder to implement all the functions. but anynumber of other components (except the adder) can be used.hint: design a combinational logic circuit to modify the input b and the “carry input” of theadder depending on the control inputs s0 and s1.important: lab grade will depend on the working of the circuit & will be checked of by your labinstructor.1. is the output valid for the following input combinations: a. s0 = 0, s1 = 0, a = 7, b = 3? b. s0 = 0, s1 = 1, a = 7, b = 3? c. s0 = 1, s1 = 0, a = -4, b = -5? d. s0 = 1, s1 = 1, a = -8, b = 6? 2. what is the range of inputs (for both a and b) that will produce the valid output for all the functions?
Answers: 3
You know the right answer?
Create a newsletter using word processing software. Directions In this assignment, you'll use a word...
Questions
question
Mathematics, 04.02.2020 10:48
question
Mathematics, 04.02.2020 10:49
question
Mathematics, 04.02.2020 10:49