Chemistry, 01.09.2019 07:30 Keo247

What is the purpose of the universal indicator? how does it indicate a chemical reaction? does the indicator give any particular indication dor exothermic or endothermic reactions?

Answers: 1

Show answers

Answers

The purpose of an universal indicator is to test wether a solution is acid or if its a base. It changes colors according to the PH's. It helps a lot in the indication of a chemical reaction because it can say if each component loses or gains protons depending upon the acidity or basicity of the solution being tested.An universal indicator can say if a determined solution proves to be endothermic or exothermic. If the solution is not tested as acid or base then we cannot knwo if there will be an endothermic reaction or an exhotermic one

Answer from: Quest

b) mutualism

hope this : )

Answer from: Quest

assuming that your periodic table has eighteen columns, you should highlight the four elements in the third column from the left of the table.

explanation

neutral atoms of elements after calcium contain d electrons. the energy of d orbitals of a particular main shell lies between the energy of the s and p orbitals of the next main shell. for example, electrons in the $3d$ have energy higher than those in the $4 s$ orbital while lower than those of the $4 p$ orbital.

by the aufbau principle, electrons fill orbitals one at a time, starting from those of the lowest energy. the $4s$ orbital is therefore filled right after $3p$ orbitals and before $3 d$ orbitals.

potassium has electron configuration $[\text{ar}] 4 s^{1}$ and calcium $[\text{ar}] 4 s^{2}$ . the s orbital of a main shell holds a maximum of two electrons. the next element would thus have the electron configuration $[\text{ar}] 4 s^{2} \; 3d^{1}$ and satisfy the requirements.

a neutral atom of the element contains three electrons on top of the most recent noble gas element. it should thus be placed in the third column of the periodic table. both scandium and yttrium would satisfy the conditions. an aufbau diagram indicates that the 4f orbital is filled before the 5d. however, it appears that exceptions exists for both lanthanum and actinium. neutral atoms of the two d-block elements also demonstrate the $ns^{2} \; (n-1) p^{1}$ and should be highlighted as well.

Another question on Chemistry

Chemistry, 21.06.2019 17:00

Write the complete balanced equation for the reaction between lead (iv) oxide (pbo2) and water (h2o).

Answers: 1

Answer

Chemistry, 21.06.2019 17:30

What are the major products produced in the combustion of c10h22 under the following conditions? write balanced chemical equations for each. a. an excess of oxygen b. a slightly limited oxygen supply c. a very limited supply of oxygen d. the compound is burned in air

Answers: 2

Answer

Chemistry, 22.06.2019 03:30

The atomic radius of sodium is 186 pm and of chlorine is 100 pm. the ionic radius for na+ is 102 pm and for cl– is 181 pm. in going from na to cl in period 3, why does the atomic radius decrease while the ionic radius increases? a. the inner electrons in the sodium cation shield its valence electrons more effectively than the inner electrons in the chloride anion do. b. the inner electrons shield the valence electrons more effectively in the chlorine atom than in the chloride anion. c. the outermost electrons in chloride experience a smaller effective nuclear charge than those in the sodium cation do. d. the outermost electrons in chloride experience a larger effective nuclear charge than those in the sodium cation do. e. monatomic ions are bigger than the atoms from which they are formed.

Answers: 2

Answer

Chemistry, 22.06.2019 05:50

Significant figures are digits read directly from the measuring instrument plus one more digit, which is __ by the observer.

Answers: 2

Answer

You know the right answer?

What is the purpose of the universal indicator? how does it indicate a chemical reaction? does th...

Questions