subject

Biology, 09.04.2021 14:00 demetriascott20

The faster the motor, the net emf.

A) higher
B) same
C) lower
D) direct

ansver

Answers: 2

Show answers

Another question on Biology

question

Biology, 22.06.2019 02:30

One of the purposes of transcription is to produce a sequence of bases that

Answers: 1

question

Biology, 22.06.2019 07:00

In many humans, exposing the skin to sunlight over prolonged periods of time results in the production of more pigment by the skin cells (tanning). this change in skin color provides evidence that -

Answers: 3

question

Biology, 22.06.2019 08:00

Cattle with brown fur and cattle with white fur will produce a reddish roan calf . when examined closely, the calf show about an even number of brown hairs and white hairs that give a reddish appearance when viewed from far away. the fact that both the brown fur allele and the white fur allele are expressed equally in the offspring is an example of

Answers: 3

question

Biology, 22.06.2019 09:00

Which ocean is on the eastern coast of north and south america? arctic ocean indian ocean pacific ocean atlantic ocean

Answers: 2

You know the right answer?

The faster the motor, the net emf.

A) higher
B) same
C) lower
D) dire...

Questions

question

Engineering, 26.07.2019 17:20

In machining, if the cost to purchase/regrind the cutting tool=$0.00, the optimum speed for machining time minimization would be different from the op...

question

Engineering, 26.07.2019 17:20

In turning, if the spindle speed (spindle rpm) increases by a factor of four, while the feed rate decreases by a factor of four, will the ideal surfac...

question

Engineering, 26.07.2019 17:20

Oil, with a density of ρ = 900 kg m=3 and a kinematic viscosity of v = 0.1 m^2 s^-1, flows at a volume flow rate of q 0.2 m^3 s^-1 through 500 m of 20...

question

Engineering, 26.07.2019 17:20

What is an involute profile and why is it used in gear tooth design?...

question

Engineering, 26.07.2019 17:20

If i can live with a 3% probability of failure, select a ball bearing design (independent of shaft diameter that will carry a 120 ib load at 3000 rpm....

question

Engineering, 26.07.2019 17:20

Determine the diameter of a cylindrical capillary tube needed to observe a 0.4" rise for water if the contact angle is 12°...

question

Engineering, 26.07.2019 17:20

If a cutting operation is performed at a feed rate of 5 in/min, and the feed is 0,005 in/rev, then the spindle rpm is: i. 5000 rpm. i. 1000 rpm. ili....

question

Engineering, 26.07.2019 17:20

Describe the general steps in the journal bearing design procedure. outline approach with substeps identified is fine....

question

Engineering, 26.07.2019 17:20

How are the pressure angle, pitch circle and base circle for a gear set related?...

question

Engineering, 26.07.2019 17:20

You need to design a compound reverted gear train with a 25: 1 gear ratio. (a) explain how you would go about developing this design. (b) if you were...

question

Engineering, 26.07.2019 17:20

One of the following is an extensive property: a)- density b)- volume c)- pressure d)-none of the above...

question

Engineering, 26.07.2019 17:20

1.0 kg of air at 300 k and 100 kpa (state 1) is slowly compressed in a piston cylinder (closed system). the compression process is an isothermal proce...

question

Engineering, 26.07.2019 17:20

Tool wear rate decreases with increasing: i. machining velocity and work material hardness. ii. cutting tool hardness. ii. none of the above. iv. not...

question

Engineering, 26.07.2019 17:20

Define the following terms. a drawing with the terms labeled would also be where appropriate. a. pitch circle/pitch diameter b. pinion/gear c. base c...

question

Engineering, 26.07.2019 17:20

5kg of wood is burnt in an insulated room. take the walls of the room as well as the wood as the system. the internal energy of the room will increase...

question

Engineering, 26.07.2019 17:20

The hardness of a cutting tool increases with increasing temperature. thus, it is always convenient to machine at higher speeds that lead to higher te...

question

Engineering, 26.07.2019 17:20

What are the independent and dependent variables that are taken into account during journal bearing design?...

question

Engineering, 26.07.2019 17:20

You are provided with an epicyclic (planetary) gear train with the following 30, 20 and 70 teeth on the sun, planet and ring gear respectively. (a) dr...

question

Engineering, 26.07.2019 17:20

What is a partial bearing? what is a loading situation that might lead you to use a partial bearing? how did this tie into beauchamp tower's experim...

question

Engineering, 26.07.2019 17:20

Define and give a few benefits of each of three gear train design options?...

More questions: Biology Another questions