subject

Biology, 30.03.2021 23:40 tamikalove78

HEEELP! I will give brainliest and profile thanks to the best answer! We protect our homes and gardens from pests (insects), you protect your small business with an alarm system, you protect your health by having insurance and eating well and taking appropriate medication --so why would you not protect your ranch in any way possible from predators? Why are some ranchers resistant?

ansver

Answers: 1

Show answers

Another question on Biology

question

Biology, 22.06.2019 03:30

What does the hardy-weinberg principle relate to? a. chances of survival of an organism b. frequency of alleles in a population c. natural selection in a species d. causes of evolution among organisms

Answers: 1

question

Biology, 22.06.2019 09:30

The “ecological footprint” left by a citizen of a developed nation is about four times larger than that left by a citizen of a developing nation. why is this the case?

Answers: 1

question

Biology, 22.06.2019 15:30

Why does sexual reproduction result in more genetic variation in a species

Answers: 1

question

Biology, 22.06.2019 21:00

Aclient with dysmenorrhea has been prescribed naproxen 1250 mg po b.i.d. what is the nurse's best action?

Answers: 3

You know the right answer?

HEEELP! I will give brainliest and profile thanks to the best answer! We protect our homes and gard...

Questions

question

Engineering, 13.09.2019 23:20

The highest cutting temperature is located close to the shear zone. a) true b) false...

question

Engineering, 13.09.2019 23:20

The largest source of heat generated in metal cutting is due to friction. a) true b) false...

question

Engineering, 13.09.2019 23:20

Calculate the differential pressure in kpa across the hatch of a submarine 320m below the surface of the sea. assume the atmospheric pressure at the s...

question

Engineering, 13.09.2019 23:20

Increasing rake angle will decrease the tendency for built-up-edge to form. a) true b) false...

question

Engineering, 13.09.2019 23:20

An orthogonal cutting operation is performed using a rake angle of 15°, to=0.012 in and w=0.100 in. the chip thickness ratio is measured after the cut...

question

Engineering, 13.09.2019 23:20

Write the type of chips generated at each of the following cutting conditions, and explain why. a. low cutting speed: b. large depth of cut: c. very...

question

Engineering, 13.09.2019 23:20

How are the polymeric materials classified? give examples of the plastic materials and elastomers? give the difference between thermoplastics and t...

question

Engineering, 13.09.2019 23:20

What is components? what is phases? what is tie line?...

question

Engineering, 13.09.2019 23:20

Avariable speed reciprocating compressor of mass 400 kg has a natural frequency of 16.2 hz. (a) design an optimum auxiliary mass damper, so that the m...

question

Engineering, 13.09.2019 23:20

Specific cutting energy increases with increasing the cutting speed. a) true b) false...

question

Engineering, 13.09.2019 23:20

Two standard spur gears have a diametrical pitch of 10, a center distance 3.5 inches and a velocity ratio of 2.5. how many teeth are on each gear?...

question

Engineering, 13.09.2019 23:20

Consider a wind turbine subjected to 30 km/hr steady winds. if the turbine produces 480 kw of power and the velocity downstream of the wind turbine is...

question

Engineering, 13.09.2019 23:20

You are traveling in an airplane. the engineer who designed it is, casually, on your side. he tells you that the wings were designed using the von mis...

question

Engineering, 13.09.2019 23:20

Cost of machining operations is primarily affected by tool life, power consumed and workpiece material. a) true b) false...

question

Engineering, 13.09.2019 23:20

What is the difference between "independent variables" and "dependent variables" in metal cutting operations? give three examples of each....

question

Engineering, 13.09.2019 23:20

Determine the molar air-fuel ratio for hydrogen (h2) burning with (a) 50% excess air and (b) 50% deficient air....

question

Engineering, 13.09.2019 23:20

Steam enters the high pressure turbine of a reheat cycle power plant at 3.5 mpa and 350and expands to 0.5 mpa after which it is reheated to 350°c. the...

question

Engineering, 13.09.2019 23:20

Aloan for $85,000 is to be paid in 10 yearly payments. each payment is larger by $100.00. compute the first, the fourth, and the last payment, if the...

question

Engineering, 13.09.2019 23:20

Asolid shaft and a hollow shaft of the same material have same length and outer radius r. the inner radius of the hollow shaft is 0.7r. a) if both the...

question

Mathematics, 13.09.2019 23:20

Describe the line segments. the cut sides of a wedge of apple pie parallel intersecting skew...

More questions: Biology Another questions